Amps
[Top] [All Lists]

Re: [Amps] Power handling of an SMA

To: "Sam Carpenter" <sam@owenscommunication.com>, "'Steve'" <g8gsq72@gmail.com>, <amps@contesting.com>
Subject: Re: [Amps] Power handling of an SMA
From: "Carl" <km1h@jeremy.mv.com>
Date: Tue, 26 Apr 2011 17:03:48 -0400
List-post: <amps@contesting.com">mailto:amps@contesting.com>
A 30 Ohm connector that is 1" long will not even show a bump thru at least 
6M and they are still OK on 2M.

Some UHF articles have stated they are a perfect 50 Ohms at 1296, dont 
know.I use them at low power on 2M FM gear including the 400W PP 4-125A FM 
amp for contest into an old commercial 22' collinear.

Carl
KM1H

----- Original Message ----- 
From: "Sam Carpenter" <sam@owenscommunication.com>
To: "'Steve'" <g8gsq72@gmail.com>; <amps@contesting.com>
Sent: Tuesday, April 26, 2011 1:07 PM
Subject: Re: [Amps] Power handling of an SMA


> As your figures from Suhner shows, .5kw is all I will do with an N at 800
> and up. I think you find that with DB Spectra, Celwave, Andrews and other
> makers of filters in that range. It is pretty standard. I too agree on the
> Suhner product. I use them when I have RX tower top preamps 500' up a 
> tower
> for emp protection. They use gas plugs that fire reliably and are easily
> replaced without taking arrestor out of line. As for the PL259, it was
> designed as a DC Connector on boats and is not typically 50 ohms. When I 
> run
> a TDR Sweep of the line, they show up as 30 ohm connectors most of the 
> time.
> It does at least make them easy to identify from the ground on a new site
> because the stick out like a sore butt on a monkey on screen.
>
> Sam N9FUT
>
> -----Original Message-----
> From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
> Behalf Of Steve
> Sent: Tuesday, April 26, 2011 12:04 PM
> To: amps@contesting.com
> Subject: Re: [Amps] Power handling of an SMA
>
> Suhner data shows approx. 500W based on dielectric strength, but there's
> a second 'low SWR' curve on the chart which extrapolates to around 1500W
> at 1.3GHz. The spec. also gives 10kW for 1us. The contact resistances
> are listed as a few milliohms, so you'd be looking at 10s amps to create
> significant heating.
>
> Not all SMAs (or other connectors) are created equal. I handle many
> brands of connector; I reckon Suhner are consistently the best quality,
> and that's not pro Eu/anti US bias :-)
>
> UTI rate .141" coax for 300-400W at 1GHz, depending on the materials and
> plating. This will push the cable to max. rated temp., 125 or 150C I
> think, so might be more than you'd choose to run if you don't want to
> burn your fingers.
>
> Steve
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps 

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>