Amps
[Top] [All Lists]

Re: [Amps] The GU84B and GU78B tubes / some brief history

To: amps@contesting.com
Subject: Re: [Amps] The GU84B and GU78B tubes / some brief history
From: "Roger (K8RI)" <k8ri@rogerhalstead.com>
Date: Mon, 29 Oct 2012 15:31:52 -0400
List-post: <amps@contesting.com">mailto:amps@contesting.com>
On 10/29/2012 11:34 AM, Vic K2VCO wrote:
I presume you mean the modified B&W 852!

I remember two different models from B&W. One was the standard 850A(?) with a "stepped" coil. A lower frequency portion of about #8 wire, (80 and 40m) followed by something on the order of 1/4 " or 5/16" tube, (20 and 15m) and then a flat strap coil (10 m) mounted on top of the end ceramic/band switch. The second unit just consisted of about 5/16ths tube. I don't remember if that one had the strap coil on the end or not.

73

Roger (K8RI)



That's what I'm planning to use for my 4CX1000A amplifier. I simply
lifted the strap from the cold end of the coil so I can insert a 160m
coil. The one thing that I couldn't figure out how to do was to add a
contact in the 160m position to switch in an additional capacitor across
the loading capacitor. The rotor wiper for the B&W switch interferes
with one of the contacts no matter where you position it.

I know B&W made a version of the tank that supported 160m. I bet they
used a narrower rotor wiper.

I am probably going to gang a small rotary switch with 60 degree
indexing to the B&W tank and use it to operate relays for the grid coils
and the loading padder.

On 10/29/2012 8:23 AM, Carl wrote:
Ive even run swamped grid old glass triodes without neutralization.
Currently it is a pair of Class C 6C21's in parallel that runs up to
20M and Ive no doubt it would work higher. That amp ran 250TH's earlier.

During the 70-80's I built and sold plenty AB1/AB2 single and dual 4X1
amps and never needed neutralization, even on 10M at 5KV.

A swamped grid Class C 4X1 covering 160-10 and driven by a 32V2 is the
next project for my own use. Guess what tank circuit Im using (-;

Carl
KM1H




----- Original Message ----- From: "Vic K2VCO" <k2vco.vic@gmail.com>
To: <amps@contesting.com>
Sent: Monday, October 29, 2012 10:59 AM
Subject: Re: [Amps] The GU84B and GU78B tubes / some brief history


Why do you say that a swamped grid-driven tetrode needs
neutralization? I haven't seen this in published designs. Isn't a
50-200 ohm swamping resistor enough to stabilize the amplifier?

Agreed on the other points!

On 10/28/2012 11:57 PM, Jim Thomson wrote:
##  actually, they are not apples and oranges.  One has an extra
grid in it,
requires a regulated screen supply, neutralization, and some method
to cancel out
the Xc between the cathode and control grid, so u just cant slap a
50/200 ohm.
passive grid resistor in there.

--
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco/

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps


-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1427 / Virus Database: 2441/5361 - Release Date: 10/29/12





_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>