Pete,
On a single or multi channel scope, connect an RF sample from a loop, sense
wire, or capacitive bridge to the vertical input (or Channel A on a
multi-channel scope). However, don't be tempted to connect the transmitter
or amplifier through a coaxial "T" section direct to the scope input. At
the 100W level (70 Vrms) , most any scope can likely handle it fine into a
50-ohm resistive system. But, start adding power and VSWR from a
non-resistive line and you can quickly exceed the scope's maximum input
level.
I use two types of sampling. The first is a Bird variable coupler. A lot
of money that's really not needed for this purpose. The second type of
sample comes from a W8ZR SationPro II switching device. W8ZR designed the
RF switching unit with capacitive pre and post amp samples. Very
convenient. But, to get you started, you can use a test lead looped around
the transmission line. Increase turns to get more level into the scope as
needed as you only need enough coupling to give a clear scope image.
Absolute value in vertical amplitude is of no concern when using the scope
for relative wavform measurements.
The paddle/key input contacts on most transceivers normally rest at a high
logic level (say +3.3V or +5V). The input is normally pulled to circuit
ground with keying action from the paddle, bug, or straight key. Next, you
can parallel the transceiver's key jack (either dit or dah side) and connect
it to the External Trigger port on the scope. The scope's trigger function
can be set to pulse the sweep on a negative-going change in key line logic
(e.g., +3.3V to 0V). Set the scope time base to 5 ms/div. You now have the
ability to view the transmitted waveform and in the case of CW, you can
precisely measure the time it takes from paddle contact to RF output. The
result looks exactly like the keyed waveform figures shown in the QST
Product Reviews.
There are other ways so trigger a scope. I often trigger from Channel B,
omitting the External Trigger connection. Most newer scopes have a menu
(push button or software) to trigger from several sources, including any of
the scope input channels.
Paul, W9AC
----- Original Message -----
From: "Pete Smith N4ZR" <n4zr@contesting.com>
To: <amps@contesting.com>
Sent: Saturday, December 15, 2012 7:03 AM
Subject: Re: [Amps] Vacuum Relay
I could sure use asimple-minded explanation of how to connect my dual-trace
scope in order to get a display of system timing. The description below,
while I'm sure it is correct, doesn't get this history major far enough.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 12/13/2012 2:15 PM, Paul Christensen wrote:
A scope isn't going to tell all but it
tells a lot about a signal. They're not difficult to use
and don't have to cost a lot.
It doesn't take long to find some incredibly good buys on used Tektronix
scopes -- and at a price about half of the popular high-end wattmeters.
Folks have no problem paying $600 for a wattmeter with unnecessary high
accuracy, but seem to find no need for a scope. Is it the number of
controls that's so intimidating?
The dual trace function isn't required to determine if hot-switching
occurs, but is required to measure system timing. For station monitoring
here, the scope's Channel A is set to trigger on the keyer's output while
Channel B samples RF. This setup makes it easy to replicate the same CW
waveform measurement as shown in the QST Product Reviews. By triggering
the scope from the keyer, the waveform stays in place for timing
measurements without having to chase it with the scope's variable
time-base control.
Paul, W9AC
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|