Amps
[Top] [All Lists]

Re: [Amps] Source for replacement PS caps

To: <amps@contesting.com>
Subject: Re: [Amps] Source for replacement PS caps
From: "Hsu" <hsu4qro@gmail.com>
Date: Sat, 11 Oct 2014 07:17:59 +0800
List-post: <amps@contesting.com">mailto:amps@contesting.com>
http://item.taobao.com/item.htm?spm=a230r.1.14.305.TaGU6e&id=20636751037&ns=1&_u=bv5d2kf374#detail
 about $1/ea Philips  450V 390uF. used

-----原始邮件----- From: Chris Fox
Sent: Saturday, October 11, 2014 7:08 AM
To: steve@nr4m.com
Cc: Amps
Subject: Re: [Amps] Source for replacement PS caps

Hi Steve,

I have plenty of screw type caps.....
http://www.ni4l.com/capacitor-500v-270uf-capacitor-lot-of-8


ᐧ

Thank you

73

Chris Fox  Ni4L
828-855-8869
Ni4L Antennas & Electronics
2646 Old Wilkesboro rd
Taylorsville, NC
28681
http://ni4l.com
https://www.facebook.com/Ni4LAntennas
*Hours: Monday-Friday 9:00 am-5:00 pm Eastern*

*"Chance favors the prepared mind" *


On Fri, Oct 10, 2014 at 3:16 PM, Steve NR4M <steve@nr4m.com> wrote:

Thanks for the input, Dave.

Been looking around and, they're a non-stocked item, like you said, or
they're big $$.

I have a bunch of much shorter, snap-in caps, which I've used in the past
with good success.  They're 470 MF @ 450 VDC and 105 degree rated.  Same
dia as these, but only about 40% of the height.  Already have a PC board
made up for using 10, but easy to cut the board down to 8 to make it fit
the PS case.  If I need to make a step start, I'll have plenty of room
above the new caps where I can place it. Probably an area of about 4 x 4 x
8 inches will be available.

I may just make the time and do it my self.
Having parts on-hand makes it much better than $200 on exact fit
replacements.

73 de Steve, NR4M
On 10/10/2014 19:09, David Harmon wrote:

Availability is probably going to be the problem....
Check with Ten-Tec....if they no longer use them...ask for a
recommendation.
Check with Henry Radio....they still have screw terminal lytics.
Recently I serviced a Henry 3KD with screw terminal caps from Henry.


73

David Harmon
K6XYZ
Sperry, OK

-----Original Message-----
From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Steve NR4M
Sent: Friday, October 10, 2014 12:43 PM
To: Amps
Subject: [Amps] Source for replacement PS caps

Hello all,

Figured it was time to re-cap the PS for my Ten-Tec since they are about
25 years old.  The amp hasn't been used in a while so you just know what
will happen if I DON'T re-cap it before I use it.

I really don't want to change (mechanically) the way the originals are
mounted in order to use a different, possibly more available, cap.

Looking for suggestions on sources other than the 'usual' (Digikey,
Mouser,
etc...)

These caps are 400 MFD x 450 VDC, 85 degree, with screw terminals on top.
Terminals appear to be #10, with a 1/2 inch spacing.  Dia is 1 3/8 inch
and
length is 5 5/8 inches, or so.

100 degree would be nice and the capacity can be +/-.

Any input would be helpful. I just don't want to pay $25 per cap if I can
find similar for $15.

--
73 de Steve, NR4M

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps






--
73 de Steve, NR4M

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>