Amps
[Top] [All Lists]

[Amps] Ameritron REPLACEMENT Capacitor Board (Shameless Plug...)

To: "AMPS" <amps@contesting.com>
Subject: [Amps] Ameritron REPLACEMENT Capacitor Board (Shameless Plug...)
From: "Jim W7RY" <jimw7ry@gmail.com>
Date: Fri, 31 Mar 2017 20:35:41 -0500
List-post: <amps@contesting.com">mailto:amps@contesting.com>
All...

I now have an Ameritron rectifier-filter capacitor board available for the 
AL-82, AL-1200 and AL-1500. The board has space for ***** 10ea***** 30 mm 
diameter caps, a bridge diode arrangement with 20 1N5408 diodes, (to take place 
of the hokey daughter board arrangement in the stock Ameritron AL-82, AL-1200 
and AL-1500) and a place for the small RFC, small protection caps, and diode 
that Ameritron puts on their boards.  


Features:
- 10ea 30mm diameter 450 volt capacitors. Use 85c or 105c caps. Your choice.
- 3 Amp 1N5408 diodes
- 1/4” push on terminals can be used for all connections. Or just solder the 
wires to the board
- Terminal area is in the same location as the stock Ameritron cap board
- No more clumsy, hard to assemble daughter board for the HV diodes
- Either use one or two bleeder resistors per capacitor. Your choice of 
quantity and value
- Includes a location for optional HV OK resistors for non Ameritron 
applications (GM3SEK Triode Board)
- Has all parts as used on the stock Ameritron filter capacitor board
- High quality PCB with 2 ounce copper runs. (Standard is  1 ounce)
- lower cost 400K Ohm 1/2 watt (10 each) for the HV metering
- Has a small 10 turn pot to adjust the HV meter so it’s accurate!
- About the same size as the stock Ameritron capacitor board and mounts on the 
same standoffs as the stock board. Must remove the two middle standoffs to 
accommodate the capacitors.
- Now you can turn up the HV (use the green transformer wire) if you want to! 
With 4500 volts of capacitors.
- Capacitors mount on the “bottom” of the circuit board with the 
bleeder/equalizer resistors on the top of the board for good air flow.

I added another string of 10 resistors for a “HV ok line” that both the GM3SEK 
triode board and WD7S board requires for monitoring HV if you want to use this 
board in a home brew amplifier project! 

The board is the same size as a stock Ameritron board and mounts on the same 
mounts. I did however need the room for the caps, so the “middle posts” that 
are on the existing Ameritron board have to be removed. But with lighter caps, 
this is not an issue.

So now you can turn up the HV (wick) (and the mystery green wire) on your 
Ameritron without going over voltage on the filter caps!!

Parts for the board are around $22.00 for the board LESS CAPS. That way you can 
choose your own caps. Either 105C or 85C caps that are 30 mm with 10 mm 
pin/lead spacing can be used.

Pictures are here:
http://s900.photobucket.com/user/w7ry/library/Ameritron%20Diode%20Capacitor%20Board


Price is $27.00ea for the circuit board shipped by US mail. PayPal accepted.

Thanks!
73
Jim W7RY

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>