Amps
[Top] [All Lists]

Re: [Amps] NXP 65V LDMOS 1K80H-1800W

To: "paul@paulbaldock.com" <paul@paulbaldock.com>, Jim Thomson <jim.thom@telus.net>, "amps@contesting.com" <amps@contesting.com>
Subject: Re: [Amps] NXP 65V LDMOS 1K80H-1800W
From: Catherine James <catherine.james@att.net>
Reply-to: "catherine.james@att.net" <catherine.james@att.net>
Date: Sun, 24 Dec 2017 19:34:04 +0000 (UTC)
List-post: <mailto:amps@contesting.com>
Can it handle continuous 100% duty cycle on MID?

Sent from Yahoo Mail on Android 
 
  On Sun, Dec 24, 2017 at 12:50 PM, Paul Baldock<paul@paulbaldock.com> wrote:   
SPE say 1.5KW SSB and CW, no limit. Continuous duty modes, should be 
used on the lower 1KW or 500W ranges.

This will by my 6M amp / instant on HF / backup HF amp. I plan to limit it 1KW.

 From the manual :

"Note: ATTENTION: Never stress the amplifier with long periods in 
key-down transmission,
as this can stress the amplifier components. However, sophisticated 
Software avoids
transmitting a continuous signal in the "MAX" condition for long 
periods by switching
to "MID" power.
Note: In SSB, use of high compression is not encouraged as this can 
cause a rapid increase
in the temperature of the amplifier."

"Appears when a continuous signal is transmitted in
"MAX". After 15 sec. the amplifier will switch
automatically to "MID"."


- Paul
At 08:49 AM 12/24/2017, Jim Thomson wrote:
>Date: Sun, 24 Dec 2017 01:01:39 +0000
>From: Bill Turner <dezrat@outlook.com>
>To: Amps group <amps@contesting.com>
>Subject: Re: [Amps] NXP 65V LDMOS 1K80H-1800W
>
>
><I checked the website for SPE, looking for duty cycle specs but didn't
><see any. Does anyone know what they are?
>
><73, Bill W6WRT
>
>###  Excellent  question.  And ditto with the new Flex...power 
>genius..with its mystery 100%  ICAS rating.
>IMO, 100% ICAS means talk on ssb or cw  all day long.... but dont do 
>something stupid, like a rtty contest.
>
>##  These SS amps are typ 50% eff at best, so with 1.5 kw out 
>requires 3 kw dc input.
>Dissipation of course is 1.5 kw.    Thats a bunch.  And a huge 
>amount  if running rtty,
>FT8, any other digital mode, or FM etc.
>
>##  any tube amp running just 60% eff, would only require 2.5 kw dc 
>input...and  dissipation
>is now down to just 1 kw.
>
>##  On the lower 3 bands,  with the same tube amp on 
>160-80-40,  68-70% eff is readily achievable.
>Now the diss is down even more, to just  706-  643 watts.
>
>##  helluva big difference between  1500 watts ccs diss on the SS 
>amp..and the  643- 1000 watts
>CCS diss  of the SS amp.
>
>##  It would require some exquisite  heat sink design to be able to 
>dissipate 1500 watts  CCS of heat.
>This is where the SS amp should be using a  19 inch wide rack mount 
>heat sink, very deep, and very tall,
>like 12 inches or more, and lotsa air on it.    Loads of fins, and 
>very thin fins.
>
>## that or some elaborate cooling setup, with a liquid cooled heat 
>sink and an external air cooled radiator +
>mating water pump.
>
>##  ideally the way to manage heat is to generate less of it in the 
>1st place, like through higher eff,  which
>appears is not going to happen any time soon with typ class AB  SS amps.
>
>##  I would like to see what both these amp manufacturers  have to 
>say about  duty cycle.
>If they are  1.5 kw  ICAS,  I will pass on em for now, not for the 
>$7K price tag.
>
>Jim  VE7RF
>_______________________________________________
>Amps mailing list
>Amps@contesting.com
>http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
  
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>