CQ-Contest
[Top] [All Lists]

Re: [CQ-Contest] Coax Stubs for SO2R

To: Jukka Klemola <jpklemola@gmail.com>
Subject: Re: [CQ-Contest] Coax Stubs for SO2R
From: Jim Brown <k9yc@audiosystemsgroup.com>
Reply-to: k9yc@arrl.net
Date: Mon, 5 Oct 2015 10:07:36 -0700
List-post: <cq-contest@contesting.com">mailto:cq-contest@contesting.com>
On Mon,10/5/2015 7:20 AM, Jukka Klemola wrote:
Jim,
I thought placing double stubs on the TX line is not so critical.
The two band stopping stubs are supposed to be about quarter wave apart; on the harmonic band; and that should effectively remove the need for extended optimization.

Also, in my experience, if you get approx 30 or 35dB attenuation using one stub, you will get more than 45 dB attenuation over the whole band when measured in a 50 ohm system.

Sure -- using my DG8SAQ VNWA, I measured peak attenuation of these double stubs of 55 dB for the 80M stub pair and 59 dB for the 40M pair. BUT a monoband antenna is NOT a 50 ohm system at the harmonic frequency, and the transmitter is NOT a 50 ohm source at the harmonic frequency.

Most monoband antennas present a very high Z to the line at their 2nd harmonic, which establishes a very high SWR for the harmonic, so the Z varies over a wide range along the line. A stub works by placing a short on the line at the harmonic frequency, and is most effective if placed on the line where the Z is high. It is MUCH less effective when at a place in the line where the impedance is much less than 50 ohms.

SO -- with double stubs separated by 90 degrees at the harmonic, the second stub will always be at a high Z spot on the line, but the first will depend on where it is along the line.

There is a second issue. By their nature, the output stages of modern power amps, both tubes and solid state, produce 2nd harmonic that is only about 6 dB below the fundamental, and must be filtered by the amplifier's output network. Most of these networks are designed for 50 ohms, and that is how they are tested. If the last element of that network is a capacitor, it will be most effective if it sees 50 ohms or more as a load AT THE HARMONIC, and least effective if it sees a short. Likewise, if the last element of the filter is an inductor (Pi-L), it will be most effective if it sees Z of 50 ohms or less.

I rigged two power amps, a Ten Tec Titan and an Elecraft KPA500 with a voltage tap at their output terminal into a dummy load and into a double stub network in line with my 40M dipole. With the stub feeding either the antenna or the dummy load, the second harmonic at the output of both power amps varied by +/- 10 dB as I added short sections of coax to vary the length of the line between the amp and the stub over more than 180 degrees at the harmonic frequency.

SO -- if we put the stub in the "right" place for the power amp, we get full performance of it's harmonic suppression network plus the suppression of our stub(s), but if we put it in the "wrong" place we can lose as much as 20 dB less of the 2nd harmonic suppression of the output network.

At least my measurements show these results:
-placement not critical for double stub

As you can see from above, that's only true if the antenna is near 50 ohms at the harmonic.

-attenuation almost doubles in dB compared to one stub

Yes.


--> I have been building only double stubs nowadays.

Me too.

Another point. When you have done this amount of suppression, you will likely begin to find other sources of 2nd harmonic, as W3LPL recently observed (perhaps on another reflector), AND you may also find leakage paths in your antenna switching system. I recently replaced a vintage Six Pack with a 6x2 sold by 4O3A. I measured crosstalk in the 4O3A unit before installing it and the Six Pack after removing it and found the 4O3A unit had more than 20dB better isolation on 20M.

In hopes of picking up another 6-10 dB of isolation, I am also planning to replace some of the random vintage patch cables in my station with newly made jumpers using high quality RG213 and Amphenol 83-1SP connectors.

73, Jim K9YC



73,
Jukka OH6LI

2015-10-05 9:57 GMT+03:00 Jim Brown <k9yc@audiosystemsgroup.com <mailto:k9yc@audiosystemsgroup.com>>:

    On Sun,10/4/2015 2:59 PM, Jeff AC0C wrote:

        That's a great way to start.  Especially as the solar cycle
        fades and 10/15 are not open.  Then in the day, you run 40/20,
        and in the night you run 80/40.


    Yes, but there's a LOT more to it if you want to maximize the
    effectiveness of the stubs. It can matter a LOT (20-30 dB) where
    along the line stubs are placed, both with respect to the antenna
    and to the power amp.
    See my piece in NCJ one issue back, or download it from my website.

    For our CQP expedition, I made up double stub packs for the 40M
    and 80M CW stations only. Each pack was two stubs cut to kill the
    second harmonic, with a quarter wave (at the harmonic) connecting
    them. I didn't have time to optimize their placement, but using
    two stubs insures that you'll get at least 25-30 dB, and with
    optimized placement, another 25-30 dB.

    Stubs are less important on SSB because the likely operating
    frequencies are not directly harmonically related, whereas the
    harmonic of 3525 hits 7050, and 7025 hits 14050.

    73, Jim K9YC


    _______________________________________________
    CQ-Contest mailing list
    CQ-Contest@contesting.com <mailto:CQ-Contest@contesting.com>
    http://lists.contesting.com/mailman/listinfo/cq-contest



_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest

<Prev in Thread] Current Thread [Next in Thread>