CT-User
[Top] [All Lists]

Band Map Question

To: <ct-user@contesting.com>
Subject: Band Map Question
From: n6tv@VNET.IBM.COM (Robert A. Wilson)
Date: Thu, 14 Jul 94 09:52:48 PDT
Ref:  Your note of Wed, 13 Jul 94 23:40:14 EDT (attached)

Hi Walt,

I just had a note from KJ6TC explaining this.  The original IBM PC used
8-bit cards that could be used for IRQ 0-7 only.  When the AT-bus was
introuced, they "cascaded" another 8-bit interrupt controller to handle
IRQs 8-15.  This controller was attached to the old controllers's IRQ2
line.

In order not to obsolete any 8-bit boards that had to use IRQ2, they
set aside IRQ 9 on the 2nd controller.  You can specify IRQ 9 on your
software driver and it will work with an 8-bit card that is jumpered
for IRQ 2.  On an AT-bus, IRQ 9 is the way to get to IRQ 2.

Bottom line, you can have an 8-bit card configured for IRQ 2, or
a 16-bit card configured for IRQ 9, but not both.  Some older VGA
cards were hard wired to use IRQ 9, but apparently that is no longer
common.

73,
Bob, N6TV
----------------------------- Note follows ------------------------------
Received: from inet-gw-1.pa.dec.com by vnet.IBM.COM (IBM VM SMTP V2R2) with TCP;
   Wed, 13 Jul 94 23:55:07 EDT
Received: from sttng.mlo.dec.com by inet-gw-1.pa.dec.com (5.65/27May94)
        id AA08839; Wed, 13 Jul 94 20:53:49 -0700
Received: by sttng.mlo.dec.com; (5.65/1.1.8.2/06Apr94-0505PM)
        id AA28973; Wed, 13 Jul 1994 23:50:45 -0400
Received: from inet-gw-1.pa.dec.com by sttng.mlo.dec.com; 
(5.65/1.1.8.2/06Apr94-0505PM)
        id AA28967; Wed, 13 Jul 1994 23:50:42 -0400
Received: from cor5.pica.army.mil by inet-gw-1.pa.dec.com (5.65/27May94)
        id AA08630; Wed, 13 Jul 94 20:47:44 -0700
To: <ct-user@contesting.com>
Date:     Wed, 13 Jul 94 23:40:14 EDT
From: Waltk@PICA.ARMY.MIL
To: ct-user@sttng.mlo.dec.com
Subject:  Re:  Band Map Question
Message-Id:  <9407132340.aa14794@COR5.PICA.ARMY.MIL>
Sender: owner-ct-user@sttng.mlo.dec.com
Precedence: bulk
Reply-To: ct-user@sttng.mlo.dec.com

Hi Bob. Thanx for the clarification. What is a cascade interrupt. I have
always been puzzled by this. For some programs setting COM3 to IRQ2 does
the same thing - makes my device communicate with the computer. I have
never fully understood why this is so and why specifying one or the
other interrupt works some times and not other.
To beat an old phrase to death: "Curious minds want to know."
73 de Walt - K2WK
............................................................................
                     73 de Walt Kornienko - K2WK (FRC)
waltk@pica.army.mil  K2WK > W2JT or K2WK@N2ERH.NJ.USA.NOAM
____________________________________________________________________________

<Prev in Thread] Current Thread [Next in Thread>