TenTec
[Top] [All Lists]

Re: [TenTec] Omni VI Dilema

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Omni VI Dilema
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 21 Jan 2008 21:19:12 -0600
List-post: <mailto:tentec@contesting.com>
If you have the funds and can find a clean late serial number Omni VI Plus, 
go for it.  Other wise, a Omni VI opt is a good performing radio.

Here's some history supplied by others from this link: 
http://www.tentecwiki.org/doku.php?id=563upgrade

<snip>
Ten-Tec offers three options-ranging from $75 to $275-to upgrade your 
existing OMNI VI (Model 563) to include some or all of the new features of 
the OMNI VI Plus.

Here's the rundown:

  a.. Option 1: For $75, you can get a kit in the mail that will let you add 
DSP noise reduction, move the DSP low-pass filter to the front panel, 
upgrade the menu, and add the new tuning speed feature. Ten-Tec says the 
mods are easy to install. The procedure requires replacing two socketed ICs 
on the logic board and putting three new labels on the front-panel keypad. 
When ordering, you'll need to give Ten-Tec the number on the IC in your rig 
labeled "logic." This will assure the correct firmware. The serial number 
alone is not sufficient. To order, call 800-833-7373 or write Ten-Tec, 1185 
Dolly Parton Pkwy, Sevierville, TN 37862-3710.
  b.. Option 2: For $125, you can get factory installation of all the 
features in Option 1, plus Ten-Tec will replace all nine keypad buttons 
instead of applying new sticker-type legends.
  c.. Option 3: For $275, Ten-Tec will do a "complete factory upgrade" to an 
OMNI VI Plus. This includes everything in Option 2 plus replacement of the 
two circuit boards and wiring harness changes needed to add an optional 
filter position in the 9-MHz IF. Ten-Tec says options 2 and 3 will only be 
offered for a limited time. Call 800-833-7373 if you're interested, and you'll 
be put on a waiting list. You must pay shipping to Ten-Tec, but there is no 
charge for return shipping for customers in the continental US.

--------------------------------------------------------------------------------

>From the Ten-Tec Reflector December 22, 2001

There were three upgrade paths offered for the original Omni VI:

  1.. Option 1 added the VI+ DSP and firmware, and re-assigned front panel 
keys were provided with stickers to indicate their new functions
  2.. Option 2 was Option 1 plus new keys, rather than the stickers
  3.. Option 3 was Option 2 plus the VI+'s 9 Mhz filter board that provided 
two narrow filter positions rather than one as in the original Omni VI.
The factory considers Option 3 to be equivalent to the Omni VI+, and it is 
with the exception of the front panel labeling.

I have been extremely satisfied with my Omni VI/Opt 1 that I purchased 
second-hand from another list member. I have filled all of the filter 
positions with Ten-Tec filters, and the radio performs very well for CW and 
PSK31. Between it and my Elecraft K2, I don't see the need for another rig 
and I find myself using the Omni VI most of the time.

John Clifford KD7KGX


--------------------------------------------------------------------------------

September 11, 2002

IMO the recent questions regarding the 563 and 564 are well worth 
understanding and commenting on and is not just "beating a dead horse". With 
so many Omni VI's and VI+'s now on the used market folks want to know what's 
up.

I bought my Omni VI 563 in November 1996, one of the last Omni VI's that 
were made. I sold it this past June. Being initially disappointed in the 
prospects of the forthcoming Orion I bought an Icom 756 Pro II, a fantastic 
transceiver (but we will leave that for another time.)

In July 1997 my Omni VI was returned to TenTec for the "Option III upgrade" 
which gave the Omni VI the electrical performance of an Omni VI+. Since 1997 
the newer Omni VI+'s underwent many minor factory changes to eliminate 
problems and improve performance from earlier productions runs. IMO the 
cumulative impact of these minor changes is significant.

Here are some of the notable things I know of in no particular order:

  a.. The silk-screening of the 564 has the "Plus" on it (dah.)
  b.. The 564 has a different font silk-screened on the input keys from the 
563 keypad. Noticeable side by side
  c.. The later 564's replaced the crystal oven with a 2ppm TCXO on the 
logic board, probably the best enhancement TT did to this radio. The crystal 
oven eventually "cooks out" and will not hold frequency tolerances well. Try 
aligning one and getting it to hold frequency. The TXCO fixes that problem.
  d.. The later 564's use slightly different BFO crystal frequencies (9.0003 
USB and 9.0033LSB/CW) from earlier units, apparently to improve the alleged 
CW key click problem
  e.. The later 564's have certain changes to top and bottom foil grounding 
on certain boards to improve 10M birdies which are a major problem with this 
rig.
  f.. The BPF filter on later 564's has a broadcast band mod to improve 
intermod in the presence of strong local AM BCB or SW signals. Night and Day 
difference on my rig.
  g.. An aftermarket mod from INRAD is available to improve the SSB audio 
response involving a swap of two component values. This became a 
semi-approved factory mod. Stock audio is degraded by passing through the 
DSP chip when DSP is not engaged
  h.. Later 564's use significant amounts of SMT construction
There are others. I just have forgotten them.

If there is no difference in the 563 Upgrade III and a 564 why did TT change 
the model number, name and affix a special label on the back of Omni VI 
upgrades to distinguish them from the Omni VI+?

There are indeed differences. An early 563 and a late 564 are very different 
radios in many respects aside form the advertised feature differences.

IMO to advertise a 563 upgrade III as a 564 as I have seen done on the 
auction sights is misleading.

As for me, I still have my Omni V.9 using Carl's fabulous processor chip 
upgrade. Man what receive audio! It stays in this shack backing up the Pro 
II.

All for now.

73 de N1LQ-Dave

<snip>

73
Bob, K4TAX

----- Original Message ----- 
From: "Newell Crary" <ncrary@owt.com>
To: <tentec@contesting.com>
Sent: Monday, January 21, 2008 4:20 PM
Subject: [TenTec] Omni VI Dilema


>I have been trying to decide what radio to buy.  I have a Scout and want to
> upgrade to an Omni.  I have read a post that talked about subtle changes 
> TT
> made to the OMNI series over the production years. The poster said "An 
> early
> 563 and a late 564 are very different radios in many respects aside from 
> the
> advertised differences.."  Not knowing what these changes were or what 
> they
> corrected, would it be better to look for a late model VI+ or go for a VI
> Option III?
>
>
>
> Thanks for your input.  Also, if you have one of these little beasties for
> sale, send me an email with the particulars.
>
>
>
> Newell
>
> WX7K
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>