TenTec
[Top] [All Lists]

Re: [TenTec] Orion 565 RIT XIT stopped working from front panel but work

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion 565 RIT XIT stopped working from front panel but works ok from POD.
From: John Huffman <hjohnc@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 05 Jul 2008 08:19:43 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Reg -

I sure would like to know the details of that fix, which in-line 
components, which traces, and which resistor.

I've had the same problem.  Tried re-soldering the pins, helps for short 
period.  Tried pulling hard on the knob, sometimes that gets it going, 
but I have to pull so hard I worry about hurting something.  Tried 
cleaning pins, no joy.

It does work on its own if the radio is really warmed up.  Every time I 
think of sending it to Ten Tec, it starts working.  At Ten Tec they say 
every one that has come in for the problem, they had been unable to 
trigger the intermittent fault.

73 de K1ESE
John


Reg Unsworth wrote:
> I had this problem until the rig went in for other work to be done (the 
> usual replacement of C6, C7 and C9 on the power board).  On a previous visit 
> they had been unable to trigger the intermittent fault.  However, as the 
> fault became more permanent, they replaced inline components and pulled up 
> resistor in the RIT control circuit, hard wired small sections of track 
> involved and cleaned up the plug/sockets.  Since then it's been fine.
> 
> 73.
> 
> Reg
> 
> ----- Original Message ----- 
> From: "Jerry Volpe" <kg6tt@arrl.net>
> To: <tentec@contesting.com>
> Sent: Saturday, July 05, 2008 4:03 AM
> Subject: [TenTec] Orion 565 RIT XIT stopped working from front panel but 
> works ok from POD.
> 
> 
>> Remember a number of comments on this subject. Mine stopped working...
>> sometimes it will bounce between 0 and -10 but that is about all. I can
>> set up the remote POD for RIT XIT and it works great from there....
>> pressing the front panel RIT control causes the proper clear. The RIT
>> XIT buttons come on as they should.  Running 2.062a. Reloaded firmware
>> numerous times. Did RAM and Hardware RESETS numerous times as well.
>>
>> For those who have experienced this.... what were your resolutions?
>>
>> 73,
>> Jerry, KG6TT
>>
>> -- 
>> KG6TT
>> Ralph Jerald "Jerry" Volpe
>> ARRL Member, VE, East Bay Division
>> FISTS Member 12304
>> Solano County
>> CM88xg
>>
>> 788 Chestnut Drive
>> Fairfield, CA 94533
>> USA
>>
>> kg6tt@arrl.net
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>