TenTec
[Top] [All Lists]

Re: [TenTec] Help with a probably stupid question

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Help with a probably stupid question
From: "John T. Fleming" <W3GQJ@embarqmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 6 Aug 2008 20:25:25 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Bruce,

Look at the PDF document for the Orion V2 mod.  It will show you how to take
the rig apart.

http://rfsquared.com/file_download/22

73,
John

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Bruce McLaughlin
Sent: Wednesday, August 06, 2008 8:05 PM
To: n4py@arrl.net; 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Help with a probably stupid question

OK.  I do thank you.  A number of years ago I removed a cover from another
radio and somehow managed to remove two extra screws which turned out to be
the speaker mounting which caused the speaker to come loose, fall onto the
circuit board and wreak a few things.  Ever since then I've been a little
cautious.

Bruce - W8FU

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of n4py@arrl.net
Sent: Wednesday, August 06, 2008 7:09 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Help with a probably stupid question

There are 12 torque screws you have to remove from the back.  All these are 
along the edge of the cover on the back of the radio.  Then each cover has 4

large side screws to remove.  That's it.

Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message ----- 
From: "Bruce McLaughlin" <bmclaugh@bex.net>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Wednesday, August 06, 2008 7:04 PM
Subject: [TenTec] Help with a probably stupid question


>I have been having problems with RF getting into the headphone line of my
> Orion II when its operated with my linear amp.  There is no problem with
> transmitting. Ten Tec was kind enough to send me a little circuit board 
> with
> instructions on how to install it.  Unfortunately, the instructions did 
> not
> include how to remove the top and bottom covers.  Neither does the owner's
> manual.  I see a number of small screws running along the back edge of 
> both
> the bottom and top covers along with two large screws on each side. The 
> back
> cover screws are removed with the wrench included with the rig.
>
> I assume those screws should be removed but I want to be sure I remove 
> only
> the necessary screws and not something which should not be removed.
>
> Can anyone help me.  I am particularly interested in knowing how many of 
> the
> back edge screws should be removed, etc.
>
> As I said . . . I realize this is probably a stupid question but then 
> again
> when it comes to such questions I have no shame.  Thanks for any advice.
>
> Bruce - W8FU
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
Internal Virus Database is out of date.
Checked by AVG - http://www.avg.com 
Version: 8.0.138 / Virus Database: 270.5.10/1586 - Release Date: 8/1/2008
6:59 PM

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>