TenTec
[Top] [All Lists]

Re: [TenTec] Omni 3 (was new RX366 sub receiver)

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Omni 3 (was new RX366 sub receiver)
From: Carl Moreschi <n4py2@earthlink.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 28 Sep 2011 08:41:00 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
My N4PY software can use a Perseus, Flex, or SDR-IQ radio as a 
panadapter with the Omni VII.  The IF on the Omni VII is not compatible 
with LP-Pan.

Carl Moreschi N4PY
121 Little Bell Dr.
Hays, NC 28635
www.n4py.com

On 9/27/2011 9:50 PM, Jerry Haigwood wrote:
> Glenn,
>      What is the IF of the OMNI VII and does it have an IF output?  Just
> curious because the Elecraft P3 input is programmable from 455KHz to
> 21.7MHz.  Also, I am thinking that N4PY has a couple of solutions for the
> ONMI VII.  I believe his software supports LP-Pan along with other SDR
> receivers.
> Jerry W5JH
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of Keith Hamilton
> Sent: Tuesday, September 27, 2011 8:23 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Omni 3 (was new RX366 sub receiver)
>
> oh really???
>
> Keith N8CEP
>
>
> On Sep 27, 2011, at 9:01 PM, Jerry Haigwood wrote:
>
>> Or buy a Elecraft K3!
>> Jerry W5JH
>>
>> -----Original Message-----
>> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
>> On Behalf Of Glenn
>> Sent: Tuesday, September 27, 2011 7:52 PM
>> To: f28noumena@verizon.net; tentec@contesting.com
>> Subject: Re: [TenTec] Omni 3 (was new RX366 sub receiver)
>>
>> Oh...... No waffle maker, juicer, beer cooler or coffee spout????
>>
>>
>> Guess I'll wait for the Orion 4 or 5.... Perhaps Then,
>> Ten Tec will have an actual real time band scope for the Omni 7 that has
>> been
>> promised for almost 5 years........
>> No...probably not...... guess I'll just wait for the Orion 17 or 18 or 19
> o
>> 20.......
>>
>>
>> WA4AOS Hi Hi
>>
>>
>>
>>
>>
>> -----Original Message-----
>> From: Gene Freund<f28noumena@verizon.net>
>> To: Discussion of Ten-Tec Equipment<tentec@contesting.com>
>> Sent: Tue, Sep 27, 2011 3:55 pm
>> Subject: Re: [TenTec] Omni 3 (was new RX366 sub receiver)
>>
>>
>> new Omni III features:
>>
>>      1. 250 Yeasu-stomping watts output!
>>      2. Replaced outdated color display with modern 3-D HD display.  2 pair
>
>> 3-D goggles included!
>>      3. LCD technology built into faceplate - on the fly choice of rig
> color
>>
>> schemes: mix and match background and label colors or select
>>          pre-programmed color schemes, such as "Classic Corsair,"
> including
>>
>> customizable Ten-Tec "dot!"
>>      4. Two sub receivers with 3-D spectrum display of diversity recepton!
>>      5. No phase noise.  Period.
>>      6. Introducing EZ financing plan administered by a former GMAC parter
>> (you'll need it)!
>>
>> and unique accessories including:
>>
>>     3-D Pro Headset - integrating headphones, microphone and 3-D HD
> goggles!
>>
>> (couldn't resist)
>>
>> de N8KUA
>> .
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>