Here is what Ten Tec told me years ago: "If there is a diode just to the left
of the MC74HC573 chip (third connection on the left edge of the card) place a
jumper across it. Depending on the model of the rig, there will be one diode,
two diodes or a jumper. The Omni series requires a jumper for proper readout. '
I don't remember having any problem doing this, and I remember that it worked.
Hope this helps.
Carl, K4SEV
Enviado desde mi iPhone
> El mar 9, 2016, a las 1:56 AM, Froiseth Richard <Rfwd6dok@centurylink.net>
> escribió:
>
> Mike,
>
> Thanks for responding to my question.
> I bought the Omni VI + from Ten Tec a few years ago and the radio came with
> the board installed.
> There were some things going on in my life at that time and I didn’t have a
> chance to check out the board or the rest of the radio. I know that sounds
> silly, but that's what happened, anyway do you know if you can tell if the
> mod has been done by looking at the board? There is a note in the manual
> stating if the board came out of anything other than a 563 or 564 call the
> factory for modification details. I guess I can shoot them off an e-mail and
> hope they respond.
> I was hoping that someone on here could answer my question.
>
>
> 73’s
> Rich, WD6DOK
>
>
>
>
>
>
>
>> On Mar 8, 2016, at 6:25 PM, Mike Bryce <prosolar@sssnet.com> wrote:
>>
>> silly question, but did this start to act up or did you buy a voice card and
>> add it to the radio?
>>
>> There is a modification that needs to be done to the card if it came out of
>> the paragon and into the Omni V/VI. I don’t recall what it was, but it was
>> rather simple
>>
>> mike, wb8vge
>>
>>
>> Mike, WB8VGE
>> SunLight Energy Systems
>> The Heathkit Shop
>> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
>> J e e p
>> o|||||||o
>>
>> A man with one clock knows what time it is. A man with two clocks is never
>> sure.
>>
>>
>>
>>> On Mar 8, 2016, at 4:45 PM, Froiseth Richard <rfwd6dok@centurylink.net>
>>> wrote:
>>>
>>> I have an Omni VI + with the Voice Synthesizer Board #257 installed.
>>> When I press the voice button on the front of the radio the voice announces
>>> the following:
>>>
>>> 80m, 40m announces 29731 no matter where you are tuned.
>>> 12m, 15m and 20m announces 429731 no matter where you are tuned.
>>>
>>> My understanding is the board should announce the freq. you are presently
>>> tuned.
>>>
>>> Can anyone shed some light on this problem?
>>>
>>> 73’s
>>> Rich, WD6DOK
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>> On Mar 2, 2016, at 5:09 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>>>>
>>>> Don't use the 500hz and 250hz filters. Put an Inrad #762 600hz filter in
>>>> the 1000hz slot: http://users.vnet.net/btippett/inrad_.htm
>>>>
>>>> 73, Barry N1EU
>>>>
>>>>> On Wed, Mar 2, 2016 at 11:57 PM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>>>
>>>>> Anyone have one or all of these filters excess to your needs. Looking for
>>>>> the TT versions or Inrad versions.
>>>>>
>>>>> Thanks for any info,
>>>>>
>>>>> Tim , AB4B
>>>>> Rogersville ,AL
>>>>> 35652
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|