TenTec
[Top] [All Lists]

Re: [TenTec] TenTec Digest, Vol 168, Issue 24

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] TenTec Digest, Vol 168, Issue 24
From: Bwana Bob <wb2vuf@verizon.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 26 Dec 2016 18:11:10 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
If slotting the top doesn't work, file it off flat, drill out the screw and re-tap the standoff.

Bob WB2VUF


On 12/24/2016 2:45 PM, Paul A. Ramey wrote:
Barry,

If you have a drill press, I would use a reverse, left hand drill bit.


On 12/24/2016 11:00 AM, tentec-request@contesting.com wrote:
Send TenTec mailing list submissions to
    tentec@contesting.com

To subscribe or unsubscribe via the World Wide Web, visit
    http://lists.contesting.com/mailman/listinfo/tentec
or, via email, send a message with subject or body 'help' to
    tentec-request@contesting.com

You can reach the person managing the list at
    tentec-owner@contesting.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TenTec digest..."


Today's Topics:

    1. HELP with broken off screw threads (Barry N1EU)
    2. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
    3. HELP with broken off screw threads (Tom Hellem)
    4. Re: HELP with broken off screw threads (Barry N1EU)
    5. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
    6. Re: HELP with broken off screw threads (Bryan Lee Cornwell)
    7. Re: HELP with broken off screw threads (Mike Bryce)
    8. Re: HELP with broken off screw threads (Barry N1EU)
    9. SOLVED Re:  HELP with broken off screw threads (Barry N1EU)


----------------------------------------------------------------------

Message: 1
Date: Sat, 24 Dec 2016 15:02:05 +0000
From: Barry N1EU <barry.n1eu@gmail.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: [TenTec] HELP with broken off screw threads
Message-ID:
    <CAFmfzDs=+mikAufBSFOPgj33cg=tLnbDK0A0i7X7GC8WjKo0Zg@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

The threaded end of an aluminum screw broke off in one of the PCB mounting posts in my Omni 6+. Please have a look here: http://n1eu.com/screw1.jpg

I'd very much appreciate advice on how to remove that screw end.

Thanks & 73,
Barry N1EU


------------------------------

Message: 2
Date: Sat, 24 Dec 2016 16:06:59 +0100
From: "Peter Frenning [OZ1PIF]" <peter@frenning.dk>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] HELP with broken off screw threads
Message-ID: <66140d57-69b6-c3f1-0bdf-6c5c64c6a16c@frenning.dk>
Content-Type: text/plain; charset=utf-8; format=flowed

Den 24-12-2016 kl. 16:02 skrev Barry N1EU:
The threaded end of an aluminum screw broke off in one of the PCB mounting posts in my Omni 6+. Please have a look here: http://n1eu.com/screw1.jpg

I'd very much appreciate advice on how to remove that screw end.

Thanks & 73,
Barry N1EU
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

Sorry Barry, I only get a partial picture...




---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>