TenTec
[Top] [All Lists]

Re: [TenTec] Power Mite PM3A CW offset????

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Power Mite PM3A CW offset????
From: Steve Ellington <steven4lq@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 3 May 2017 08:27:52 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Mike: Thanks for the HW-8 info. I looked at the HW-8 schematic and they
shift the VFO via a diode/capacitor triggered by the relay voltage. That's
perfect for the Power Mite. I'll give it a try. The HW-7 is like the
PM...No cw offset. This reminds me of the National NCX-3 I tried many years
ago. No offset or RIT made it almost impossible to use. 73 Steve n4LQ

On Tue, May 2, 2017 at 11:39 PM, Mike Bryce <prosolar@sssnet.com> wrote:

> On the HW-8, a direct conversion transceiver, heath instructed the
> operator to tune from the high side down. In other words start at 7.1 and
> tune lower in freq, keeping the receiver on the high side of the bandwidth.
>
> that way when a station answered, it would be on the low side, but
> completely copyable.
>
> There was a slight offset between tx/rx because heath allowed the VFO to
> shift a bit in tx. The actual shift depends on the band
>
>
> Mike, WB8VGE
> SunLight Energy Systems
> The Heathkit Shop
> http://www.theheathkitshop.com/
> J e e p
> o|||||||o
>
> > On May 2, 2017, at 11:21 PM, Steve Berg <wa9jml@frontier.com> wrote:
> >
> > This sounds a lot like my Heath HW-7.  It has a bit of an offset, but
> not much of one.  It is also a direct conversion rig.
> >
> > Steve WA9JML
> >
> >
> > On 5/2/2017 7:30 PM, Steve Ellington wrote:
> >> I'm playing with a PM3A and noticed there is no CW offset. There's
> nothing
> >> mentioned in the "manual" and the VFO has no means of shifting frequency
> >> when the key is down. This is a mystery since without this feature,
> anyone
> >> coming back to my CQ will be zero beat and couldn't be heard. I have
> done
> >> some Googling. Offset and Powermite don't seem to be used together.
> >> I guess I could rig up a varicap to do the the job. Does anyone have any
> >> experience with this rig?
> >> Note: I am not using crystals nor does it have any xtal jack. I'm using
> the
> >> same VFO for xmt and rx.
> >>
> >> Shiftless in Charlotte
> >>
> >> Steve N4LQ
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >
> >
> > ---
> > This email has been checked for viruses by AVG.
> > http://www.avg.com
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>