I guess my answer was a bit abbreviated ;-) I just meant that it takes 30
seconds to retract the element, which would be an unnacceptable delay when
changing headings, where a relay is instantaneous. The SteppIR can move 100kHz
pretty fast, but not the full length of the tape.
Larry N8LP
----- Original Message -----
From: Richard M. Gillingham
To: Larry Phipps ; towertalk@contesting.com
Sent: Sunday, September 26, 2004 11:44 AM
Subject: Re: [TowerTalk] SteppIR Vert
I just wish I had the real estate to have such a slow, worn out setup...
(grin)
Gil, W1RG
----- Original Message -----
From: "Larry Phipps" <larry@telepostinc.com>
To: <towertalk@contesting.com>
Sent: Sunday, September 26, 2004 11:30 AM
Subject: Re: [TowerTalk] SteppIR Vert
Too slow, and too much wear and tear on the SteppIR I think.
Larry N8LP
----- Original Message -----
From: Richard M. Gillingham
To: Larry Phipps ; Jim Lux ; skip ; towertalk@contesting.com
Sent: Sunday, September 26, 2004 10:51 AM
Subject: Re: [TowerTalk] SteppIR Vert
Why open an element.. Just retract it into the housing...
Just a thought
Gil, W1RG
----- Original Message -----
From: "Larry Phipps" <larry@telepostinc.com>
To: "Jim Lux" <jimlux@earthlink.net>; "skip" <k3cc@fast.net>;
<towertalk@contesting.com>
Sent: Sunday, September 26, 2004 10:41 AM
Subject: Re: [TowerTalk] SteppIR Vert
This would be a design nightmare. You might want to consider a simpler
approach. With three verticals in an equilateral triangle layout, and proper
switching, you could build a parasitic array with at least 6 beam headings.
By driving one element, shorting another to create a parasitic and opening
the third to make it inert, you can make a number of 2el beams with just a
couple relays at each base. You would have to place the relays in the
housing so that the connection between matching network could be bypassed
for the open and shorted conditions.
If you needed more than six headings, you could use both parasitics at the
same time as reflectors, giving three more directions... but this adds to
the complexity. Of course, you would have to setup a bunch of custom antenna
lengths and daisy chain the controllers.
A far simpler, higher gain, but more expensive approach would be to use 5
verticals in a box configuration with one in each corner and one in the
center. This would produce a 3 element beam in four directions firing
diagonally, with no feed switching since the center element would always be
fed. The "driven" element would use stock SteppIR settings, each "parasitic"
element would have custom settings for director and reflector lengths, plus
a relay to "open" the element.
Keep in mind that the H-plane pattern is much broader than the E-plane
pattern, so four directions would probably be OK if the centers of the lobes
can be placed on important directions such as Europe or Japan. The box
wouldn't have to be square, so there is some room for adjustment of the lobe
headings.
You could also get 8 headings by using two reflectors and two directors at a
time to fire off the sides of the box, with reduced performance, but this
adds to the complexity and probably wouldn't be necessary.
I had a 160/80 (using switched loading coil on 160) version of this design
at a contest station I had out in the country years ago and it worked great.
73,
Larry N8LP
----- Original Message -----
From: Jim Lux
To: skip ; towertalk@contesting.com
Sent: Sunday, September 26, 2004 9:14 AM
Subject: Re: [TowerTalk] SteppIR Vert
----- Original Message -----
From: "skip" <k3cc@fast.net>
To: <towertalk@contesting.com>
Sent: Saturday, September 25, 2004 9:17 AM
Subject: [TowerTalk] SteppIR Vert
> I've just ordered a SteppIR Big Vertical 40 thru 6 meters.
>
> My question is would it be feasible to make a 4 square out of 4 of them
> using a 1/4 wavelength spacing on 40 meters ???
>
> This would be 1/2 wave on 20 and full wave on 10
>
> If their were separate switch phasing lines, relay switched, and a phasing
> box to switch the direction.
>
> I have not yet calculated the lead/lag as yet for phase angles.
>
> Has anyone built or thought about a multiband 4 square ???
>
> Or is this just wishful thinking ????
>
> de Skip K3CC
I've thought quite a lot about multiband phased arrays using tunable
elements such as the SteppIR. Here's the tricky parts:
1) 1/4 wave spacing on 40 might not be what you want. You need to choose a
spacing that works out for all bands, because spacings like 1 wavelength
tend to be less useful than you might think (you get lots of lobes and
nulls, and it's difficult to control exactly where they'll wind up). But,
see later...
2) The mutual impedance will be different on the different bands (generally,
speaking, less on the higher bands, because the elements are farther apart
(in terms of wavelength), which means that your phasing networks will be
quite a bit different for each band.
3) You can use the variable length feature to help with the phasing (because
you can make the element a bit longer or shorter to add L or C to the
feedpoint impedance)
4) A square arrangement, while easy to do calculations on paper for, may not
be the optimum arrangement for you. You need to get a map out and figure out
where you want to form beams and/or nulls. It might well be that a straight
line arrangement might work out better.
5) I think the true value of a phased array is not in forming the beam, but
in forming a null. An array with 4 elements spaced a reasonable distance
apart isn't going to have a huge amount of gain, but can potentially form
very useful nulls and "low response" areas to cut down on signals coming
from areas where you don't want to talk to. This, however, requires a
substantially more sophisticated approach to the phasing network control
(the networks are the same, but figuring out the Ls and Cs is non-trivial)
If you want to fool with phase calculations with various arrangements of
elements, I've got an excel spreadsheet I can send you that allows you to
specify the x,y position of your elements, as well as the phase and
magnitude of the current in the element, and it calculates the horizontal
pattern. It can also use Excel's optimizer to try and find the currents that
produce a pattern as close as possible to what you desire. (Of course, that
leaves the hard part of the feed networks).
Jim, W6RMK
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.766 / Virus Database: 513 - Release Date: 9/25/2004
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|