Any equivalent in Europe, or even in Belgium? ( since the software is german
).
Thanks for a shout.
Jos on4kj
-----Message d'origine-----
De : towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] De la part de Jerrry BOYD
Envoyé : mardi 28 novembre 2006 2:25
À : Tower Talk List; Jim Lux; Richard M. Gillingham
Objet : Re: [TowerTalk] custom aluminum panels
Me too! Been trying to find someone to fabricate and professionally label a
new front panel for an amp. Looks like this might do it. Thanks for
posting Jerry N7WR
----- Original Message -----
From: Richard M. Gillingham<mailto:rmoodyg@bellsouth.net>
To: Tower Talk List<mailto:towertalk@contesting.com> ; Jim
Lux<mailto:jimlux@earthlink.net>
Sent: Monday, November 27, 2006 6:23 PM
Subject: Re: [TowerTalk] custom aluminum panels
WOW. Thanks. I've been looking for a service like this for some time.
Gil, W1RG
----- Original Message -----
From: "Jim Lux" <jimlux@earthlink.net<mailto:jimlux@earthlink.net>>
To: "Tower Talk List"
<towertalk@contesting.com<mailto:towertalk@contesting.com>>
Sent: Monday, November 27, 2006 9:08 PM
Subject: [TowerTalk] custom aluminum panels
>A great resource when you need an aluminum panel with holes, notches,
> lettering, etc. at a reasonable price is a company called Front Panel
> Express.
>
> http://www.frontpanelexpress.com/<http://www.frontpanelexpress.com/>
>
> you download their software, design up your panel and send the order
> off electronically. They've got libraries with all manner of weird
> cutouts: D holes for things like BNC connectors, Sub D multipin
> connectors. And, they do holes of all shapes and sizes (including
> tapped), pocket milling, engraved legends, etc. Essentially anything
> a good NC mill can do to a piece of flat aluminum.
>
> You can also get it finished in a variety of passivations, or paint,
etc.
>
> Delivery time is usually less than a week (depending on how much you
> want to pay).
>
> It's remarkably cheap (standard 19" rack panels 4 U high with a bunch
> of connectors run around $50, and most of the cost is the aluminum..
> tapped holes are something like 0.38 each and so forth) and I daresay
> you'd have a very hard time duplicating their product at home, unless
> you have a good NC mill and a lot of programming time.
>
> We use them at work for things like breadboarding microwave circuits
> (you know, you get all those little modules from Minicircuits and
> need to screw them down to something). I've made waveguide pass
> through panels (the WG opening and the 4 tapped holes for the flange
> bolts) to mount into the side of, strangely enough, a NEMA 4 Hoffman
box.
>
> Truly an amazing service.
>
> The software and machinery is made by a German company, and
> occasionally, the software displays an error message in German, but
> you can figure it out, and go on. The place you send your order to
> and which does the work is in Washington state.
>
>
> No excuse for ugly connector panels where the bulkhead feed throughs
> keep spinning when you tighten the connector!
>
> Jim, W6RMK
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com<mailto:TowerTalk@contesting.com>
>
http://lists.contesting.com/mailman/listinfo/towertalk<http://lists.contesti
ng.com/mailman/listinfo/towertalk>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com<mailto:TowerTalk@contesting.com>
http://lists.contesting.com/mailman/listinfo/towertalk<http://lists.contesti
ng.com/mailman/listinfo/towertalk>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|