Towertalk
[Top] [All Lists]

Re: [TowerTalk] US Tower HDX-689 Sheave replacement

To: akozak@hourglass.com, larryj@teleport.com, towertalk@contesting.com
Subject: Re: [TowerTalk] US Tower HDX-689 Sheave replacement
From: mikflathead@aol.com
Date: Mon, 11 Mar 2013 17:49:40 -0400 (EDT)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
 Be careful doing that. Sometimes the grease in the bearing will catch fire.

 

 

-----Original Message-----
From: Al Kozakiewicz <akozak@hourglass.com>
To: larryjspammenot@teleport.com <larryj@teleport.com>; towertalk 
<towertalk@contesting.com>
Sent: Mon, Mar 11, 2013 10:24 am
Subject: Re: [TowerTalk] US Tower HDX-689 Sheave replacement


NO!

At worst, a local machine shop can press a new bearing into a sheave.  
Depending 
on the diameter of the sheave, your own resourcefulness and tool collection, 
you 
can often do it yourself with a large bench vise and some sockets.

In fact, with an aluminum sheave, I'd bet that you could heat the sheave up in 
a 
oven; put the bearing in a freezer; and the two components would slide together 
without a press!

Al
AB2ZY

________________________________________
From: TowerTalk [towertalk-bounces@contesting.com] On Behalf Of 
larryjspammenot@teleport.com [larryj@teleport.com]
Sent: Monday, March 11, 2013 10:16 AM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] US Tower HDX-689 Sheave replacement

Does that mean that the tower has to go back to UST to have such things 
installed? Just curious, before I look at spending lots of $$$$ for a tower 
that 
might need to have the same thing done a few years down the road. That could be 
VERY expensive!

LJ



-----Original Message-----
>From: K7LXC@aol.com
>Sent: Mar 11, 2013 6:53 AM
>To: towertalk@contesting.com, rich@n7tr.com
>Subject: Re: [TowerTalk] US Tower HDX-689 Sheave replacement
>
>>  Im looking for the 5 inch OD Pulley Sheave for the  HDX-689. This is for
>the ? in cable.   I need to order a few of these  as I'm replacing all the
>cables on the tower right now.  I know US Towers  had them, but wanted to
>see if anyone else has replaced them from another vendor  for a better price.
>
>    Typically these are UST proprietary. That is, they  make an aluminum
>sheave and then press a sealed bearing into it. You'd have to  do the same
>thing.
>
>Cheers,
>Steve     K7LXC
>TOWER TECH
>US Tower factory authorized installer
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

 
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>