The examples all show screen shots so that is probably not much help for you.
Make sure the MicroHam software specifies a port for WinKey.
In Writelog, go to ports and set CW keyer type to K1EL Winkey. Leave SO2R
Control set to none.
Set the radio button for CW to the com port that you specified in the MicroHam
software.
That should get you to the point that CW messages are keying things.
You say it works for N1MM+ so have to figure it is something the WriteLog setup.
Randy K5ZD
-----Original Message-----
From: WriteLog <writelog-bounces@contesting.com> On Behalf Of
rgarrett5@comcast.net
Sent: Sunday, August 2, 2020 6:37 PM
To: 'Robert' <woodr90@gmail.com>
Cc: 'WriteLog Reflector' <writelog@contesting.com>
Subject: Re: [WriteLog] CW Jitters
Hello Robert et al,
So under “CW” in the configuration section, I have 8 choices. The only
MicroHam setting is for MKR which is used with SO2R. I’m a visually impaired
guy so if there is another place on the screen where Microham MKII is listed,
please tell me. I certainly am not able to read it.
The only other setting for CW is the five choices I assume for LPT and com
ports. Any input appreciated. 73, Bob K3UL
From: Robert <woodr90@gmail.com>
Sent: Sunday, August 2, 2020 4:43 PM
To: rgarrett5@comcast.net
Subject: RE: [WriteLog] CW Jitters
FWIW
I’m hooking up winkey2 this month
have used the PC generated CW in past – normally it works great but think RF
got computer few times on that transistor interface
and it would jitter & quit. then reboot…
check the writelog settings, if you’re got Microham 2 set in CW window, then
it’s a mystery to me
My only experience with Microham was at Carl’s rental, the P40YL side had
MicroHam, Most – including me, unhooked it and used USB to RS232 or whatever
instead then hooked back up as was.
73 W5AJ
Robert
Midland, Texas
From: rgarrett5@comcast.net <mailto:rgarrett5@comcast.net>
[mailto:rgarrett5@comcast.net]
Sent: Sunday, August 02, 2020 1:24 PM
To: 'Robert' <woodr90@gmail.com <mailto:woodr90@gmail.com> >
Subject: RE: [WriteLog] CW Jitters
Hello Robert,
MicroHam MKII.
I just want to be sure I don’t have some incorrect setting where I believe I’m
using the WINKEYER in the MicroHam MKII when I’m not and actually using PC
generated CW..
From: Robert <woodr90@gmail.com <mailto:woodr90@gmail.com> >
Sent: Sunday, August 2, 2020 2:04 PM
To: Bob Garrett <rgarrett5@comcast.net <mailto:rgarrett5@comcast.net> >
Subject: Re: [WriteLog] CW Jitters
How are you interfacing from writelog/computer to Rig on CW?
PC generate?
Winkeyer?
Etc?
W5AJ
On Sun, Aug 2, 2020, 7:10 AM <rgarrett5@comcast.net
<mailto:rgarrett5@comcast.net> > wrote:
Greetings,
I've had an ongoing problem using WriteLog with CW breaking up or having some
delays, speeding up or slowing down, mostly speeding up in the middle of a
message. Any thoughts as to why this behavior? 73, Bob K3UL
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com <mailto:WriteLog@contesting.com>
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|