Hello I using a Heil headset with the omni 6+. First: need very high mike-gain and processor-level for moderate output Second: some people told me that there is a "brrrrr" sound in the background on
I am looking for a good mike for my OMNI 6+. I know the TT 705, Shure 444 and D104 are great mikes for the OMNI 6+. But i saw a used Shure Mod. 450 II in a hamradio magazine here in DL. Is there a bi
Hello maybe I have a similiar problem with my OMNI 6+, but only on 80 meter. Sometimes the TX-signal jump away and then there is also jump in the sidetone and the external SWR-meter display a bad SWR
Why I cant browse this reflector on Yahoo just to read the messages? I have to join this group!!!!!! How many groups you have to join, just to read the messages in you HAM life? So I still stick here
But all the time first join then unsubscribe and so on. Come on 73 de Harry, DK2GZ _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.co
Hello my trusty OMNI 6+ doing well on all bands, also on 160. I do not need to readjust something in a menue the whole daily operating session. I like to operate and not fooling around. Hi! 73 de Har
Hello my OMNI 6+ is maybe oscillating on 80 meter. I can here my tx-signal very wide on 80 meter, about 500 KHZ up and down on a second receiver. Also the external SWR-bridge shows a bad SWR, but the
Hello I had replaced diodes D6, D7, and D8 on the Low Pass Filter Board last night. Problem was an oscillating TX on 80 meter. I have installed 1N41007. Now the TX is absolutly stabile but the the RX
Hello all found on the PCB now how to place the diodes. Was to dark yesterday night. 73 de Harry, DK2GZ _______________________________________________ TenTec mailing list TenTec@contesting.com http:
Hello getting the 80 meter problem now fixed a few days ago. Bad diode in the low pass filter board. But suddenly today the TX produce only about 20 watt on all bands. Even less on 160. There is no A
Hallo Rick glaube habe die BAT-14 Diode im LP board durch ESD zerschossen. Must go to hannover by train today, back in the late evening. 73 de Harry, DK2GZ ___________________________________________
Hello all here are the first impressions after one week of usage(used an OMNI 6+ for several years before): PRO: 1. RX is nice, but the factory default setting for the AGC a little to noisy for my ea
Hello Jack I set the prog AGC: Hang 00.00 decay 5 db/s threshold 47.87 uV NR off or NR 3-5 then you can deal with the decay up or the threshold a little Harry, DK2GZ _________________________________
Hello to transfer also the BW and Mode with the A-->B button, simply activate the tracking in the menu. Then also the same BW and Mode is on the 2. RX Cant tell you the menu item yet because my ORION
Hello I have read the discussion about the OMNI 6+ and the roofing filter in the Orion. Here some notes by a CW operator: Nearly a week ago I was fighting very hard with me to switch back to the OMNI
Hello TT-Group I just installed the 1.372 firmware. Two things i noticed in difference to 1.371: 1. Click in headphone Using headphones and listen only the main RX, there is a click in right headphon
Bob W2WG I just did some check again. I am dont use BIN-RX mode But the click is more present on 160/80/40 and less on 17 Meter and up I am using LCW for CW on all bands. 73 de Harry, DK2GZ _________
Some further investigation: When QSK-Delay is 8% and above the click is gone, but at 7% and less the click is present. 73 de Harry _______________________________________________ TenTec mailing list
Hello here the same funny things happen from time to time. Lost the main rx, lost the sub-rx Signals sounding strange like aurora signals. Power off/on start the Orion normal again. But will not do i
Hello TT-Fans, I decided to go back to firmware 1.371 today. I am doing 99% CW this this radio. Why did I reload the 1.371 firmware: 1. the new keyer function does not work for me, still stuck in cut