Running for about 36 hours in the VA QSO party I had the following issues: 1. 3 instances of lost receive audio -- solved by turning radio off and on. This was a common occurrence under pre - 1.371 a
Any chance this is rf in the shack? (or at least in the radio?) I appreciate the suggestion and I have considered it. There is always a chance of RF in the shack either from unbalanced antenna loads,
I submit the only way to check the NR function is by listening. It either works or it doesn't. It hasn't worked since version 1.371. K4ia "Buck" Fredericksburg, Virginia USA _________________________
Works = noise goes away. (ver. 1.371) Does not work = push the button and nothing happens, or Does not work = push the button and distortion introduced (everything after 1.371) Don't need to be a sof
Lee I say all that and raise you one. I haven't found ver 2 to be any more stable than the early versions of 1.3xx. I am getting the raspy distorted audio on receive and the strange loss of receive a
Degrades?...strange result! This implies a noise bandwidth of ~800 Hz. Simply turning DSP BW to 100 (which has an actual BW of 150 Hz) should **improve** S/N by 5.2 dB. I believe what he is saying he
I have been trying to get back into digital modes and notice that the audio output from the AUX I/O connector pin 4 seems to depend on the volume control instead of being a line out as described in t
The internal speaker and (78) ExtSpkr are working properly controlled by (44) and (45). However, Muting and Volume Control (44) and (45) in the latest firmware (v2.032) affect the Line Out as well as
I was running 2.055 and upgraded to 2.056 - the audio from the Aux is still dependent on the volume control and I have to listen to the screeching to run digital modes. Others have reported this is "
Red faced and embarrassed, I am compelled to exhibit the depth of my ignorance so that others may benefit from my folly: It seems I had the cables plugged into the Remote Encoder jack instead of the
I was very careful to take RESPONSIBILITY for plugging the AUX cable into the Remote jack all by myself. I left it to someone else to point out how easy that is to do and to speculate that perhaps a
That would be equivalent to your driver above grabbing the track's PA system and griping to the spectators rather than the engineer, who can actually do something about the problem. ;-) I still don't
setting to confirm Bug My Orion I does not have this problem. K4ia "Buck" Fredericksburg, Virginia USA _______________________________________________ TenTec mailing list TenTec@contesting.com http:/
I can confirm that turning on the software NB, then NR, then Notch will also kill the audio in the Orion 1 running 2.056 when you go to adjust the Notch. This only seems to happen if the NB is on 2.
Stop whining? Sell the radio? Sorry - that's not the point. Fact is - Orion is a work in progress. Can we agree on that? Is anyone going to try to make the case that Orion is working properly in ever
Here's a new one. I go to the menu to change the EXT T/R Delay so my amp won't be trying to QSK between every CW character. Menu > Tx > EXT T/R Delay 1. I am not using a keying loop. When I rotate th
Barry I think you have hit the proverbial head of the nail. The problem is a failure to communicate. k4ia Craig "Buck" Fredericksburg, Virginia USA _______________________________________________ Ten
Given the way the radio is designed I would expect that the Main RX would always be used to control the transmissions and the Sub would be used for listening only. No, no, no I use the Sub as the TX
No one responded to say they had experienced this anomaly and I am now unable to duplicate it myself. Gary, at ditsnbits, says they have never heard of it either. Therefore, I am going to call it ope
DSP magic was not hidden in ver 1.371. It got buried in every version after that. In 1.371 it made the receiver get very quiet - no hiss, no ocean noise. I describe it as "squelch like." When a signa