I have posted this thread before...but thought would try again and see if I can come up with any new ideas or info.. Currently, I have a Paragon II and an Omni VI Plus upgraded to option 3 running of
Hi Jerry, thanks for the most informative reply -- Original Message -- From: "Dr. Gerald N. Johnson" <geraldj@storm.weather.net> To: <tentec@contesting.com> Sent: Tuesday, January 09, 2007 6:15 PM Su
Wonder what it would take to get my omni vi plus option 3 to do that? Have all filter positions filled with TT filters...but then there's Inrads.... -- Original Message -- From: "Dennis OConnor" <ad4
keep in touch and let us know how it all works out... -- Original Message -- From: "John Cox" <jecox@tri-lakes.net> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Wednesday, Janu
I had a Corsair II...and I consider the Omni vi to be superior, if I set the incomming signal on 2000 hrz and click in the N1 filter (very high pass) and also use the psb filter and 250 hrz cw filter
I would like to purchase the mike...what is your qth? Im in Pendleton. -- Original Message -- From: <k7gt@charter.net> To: <tentec@contesting.com> Sent: Wednesday, January 31, 2007 8:51 AM Subject: [
Hi all.... I have a Paragon II and an Omni VI, both hooked up to separate TT power supplies. The rigs co exist nicely, but I recently did a bit of horse trading and have a number of sealed commercial
check relay coils for the bandpass filters...My Pegasus had the same problem on 20 meters....and the relay coils were in series with one another on each side of the bandpass filter. -- Original Messa
Hi all... I recently was given one of those old TT banana mics, and I believe they have a crystal element in them. I am thinking of replacing the element with either a dynamic or a condenser mic... H
I am wondering about the fesability of tweeking my Omni VI's rtty, or fsk port for use on psk31. Has anyone done this? I am using the usual soundcard route for that mode presently.
I use something called "Ice" available from bicycle shops. Works very well for the capacitor and roller inductor bearings also. Dig out a lower voltage walwart out of the junk box to use for the ligh
Is it the filter cap you replaced? -- Original Message -- From: "john" <johnmb@nc.rr.com> To: <tentec@contesting.com> Sent: Monday, September 18, 2006 2:34 PM Subject: [TenTec] Paragon troubleshootin
Wonder what code says about installing the power supply at the breaker box and running high voltage lines to the amp in the shack? -- Original Message -- From: "Ed Cummins" <w3etc@comcast.net> To: <t
First pix!!!! http://www.vihn.net/pictures/HeavyAds/tn_100254144_1.jpg -- Original Message -- From: "Reed O. Krenn" <reed_ww3a@alltel.net> To: <tentec@contesting.com> Cc: "Rick Williams" <rick.willia
I notice the same on this end....Paragon II, 238B atu and MFJ-259B analyzer. Also, my Mirage MP-2 wattmeters indicate a different power output reading from the rig and atu if other than full power ou
A subnote...if I connect my Mirage MP-1 line sensor directly in back of my Paragon II, then the swr readings on the MP-2 and rig will jive...even on 10 meters. -- Original Message -- From: "Denton" <
Although not specific to TT's, I am wondering if there is a box that allows one to use the same antenna with two different rigs at the same time? and would allow one to transmit on the same antenna w
Been there, had that happen. My Omni VI Plus keep blowing up the finals and/or final drivers when I was using recommended Airpax breakers in conjunction with my homebrew stations power supply and bat
I should add another note... It is only my Omni VI that suffers from the blown finals when used with my battery/power supply/Airpax circut breaker setup. None of the other TT rigs I have or had in th