But some of us prefer real knobs instead of a mouse! Hey I wouldn't mind a second OII here too! B-) If you pay me $US50 I'll take it off your hands. 73, John de VK2XGJ Sometimes I pretend to be norma
I think this was advertised as "beta" software. Some common definitions of "beta" release are here: http://www.google.com/search?hl=en&client=firefox-a&rls=org.mozilla:en-US:of ficial&hs=WYe&defl=en&
I also moved to another COM port, so I'm not sure if that solved the problem or it was something else. Eventually set the USB adaptor to COM3 if I remember correctly. Try setting it to another unused
I also moved to another COM port, so I'm not sure if that solved the problem or it was something else. Eventually set the USB adaptor to COM3 if I remember correctly. Try setting it to another unused
There are some folks who are into "hi-fi" SSB at wider than useful bandwidths, with expensive gold plated microphones and audio processing gear, trying to make their 6 kHz wide signals sound like hi-
There are some folks who are into "hi-fi" SSB at wider than useful bandwidths, with expensive gold plated microphones and audio processing gear, trying to make their 6 kHz wide signals sound like hi-
Another minor glitch for the bug list: If you go to Recall button, but instead of dialing a memory and entering it, you hit Exit (just above the recall button), then it goes back to the normal screen
The radio had been running on Rx for a few hours, 20 and 80 meters. The 80m band was dead, mostly just local line noise. I am now getting the normal white spectrum, but now behind it the entire scan
Well, after a week or so of use, that's the first time I've seen that particular manifestation of the red screen. What I usually see is the white trace erasing completely, leaving just the red trace
Oops, an error in the link, Here it is: <http://s685.photobucket.com/albums/vv219/N4BE/?action=view¤t=DSC00426 --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@co
In my opinion this red screen is not an intentional indication of overload. Why would a software designer employ such exotic behavior (solid red, then moving vertical lines, etc.) just to indicate an
Oops. This could be bad for FCC certification! Just my two cents worth. I have been running color 7 (which is a lot of red) and as of yet (knock on wood) to observe the red sceen on either the waterf
I have no nearby switching supplies. But I wonder if the power supply does have something to do with it. I am using a transformer based Astron AS-50A regulated 50 amp supply, not the TT switcher. Che
Are there any retired software engineers on here who would like to volunteer to spend the summer in Sieverville and do a serious job of fixing TT's source code? Or perhaps reverse engineer the binary
Do these look familiar? http://s685.photobucket.com/albums/vv219/N4BE/?action=view¤t=DSC00426- 1.jpg Jim N4BE Hello all , I just found a problem with this new download for the Orion II . After
Could this be a DSP noise blanker or noise reduction induced distortion? The O-II (depending on the DSP version) can exhibit some audio distortion from the digital signal processing if NB and or NR i
Ic-7800. Or maybe a k3? Jim I am looking to add another back-up rig to the shack. 100% operation is CW. I am considering a Omni VI or Jupiter. What does everyone recommend? __________________________
An OCF (Off Center Fed) antenna works much better. Feed with coax. Low SWR on all bands. Good reports. I'm using one. Jim N4BE http://hamcall.net/7bandocf.html That will work, but will always be some
Using HRD sound card into rear panel auxiliary input. With speech proc off I get only about 50 watts out with max audio drive measured on rf wattmeter. The O2 meter shows 100 watts, not 50. If I turn