It's my first post and questions already! The green digit on the #544 is considerabley less bright than the other red digits; almost useless in in a a bright room. I suspect this is not normal. what
Would appreciate knowing a source and voltage for the for the small grain of wheat panel pilot light. Also need a source of the GREEN 10's digit LED. I suspect more than one TenTec model used these p
n4uw pls concact me joe k7mks -- Original Message -- Cleaning out the shack of unused items, and have the following for sale: Ten-Tec Model 962 Power Supply/Speaker. Matches Corsair II, Paragon, Omni
The green digit on my "new to me" Triton IV (Model 544) is usable but not as bright as the other 5 red digits. I've also noticed that many of these models that appear on auctions suffer from the same
Is there an easy way to apply DeOxite to the wafers of the Mode switch. Mine is quite noisy and the wafers do not appear to be easily reachable. Thanks joe k7mks _____________________________________
Ron: I will take it if it is available. I have a 253 coming and may need the cable. PayPal OK? joe k7mks -- Original Message -- I have an interconnect cable for the Omni 5 and 6 series transceivers t
I'm helping the estate of a SK find a new home for a working #253 tuner in like-new cosmetic condition with an unused copy of the manual. The remote control cable is hiding somewhere and may not be a
My recently acquired My recently acquired Corsair II, with DRIVE full CW, delivers 76 watts or so on all bands except 10 and 15 where output is slightly less. Panel meter pegs to the left and regardl
Shawn The ammeter on the Shawn The TT PS reads 13-14 A and the meter on the Corsair pegs to the left when meter switch is at IC. It should swing to the right and read essentially the same as the mete
Am looking for a Paragon PLL #81338 major loop board in working condition. Thanks for checking. Joe k7mks _______________________________________________ TenTec mailing list TenTec@contesting.com htt
Does anyone have a copy of the Geihl chip instructions that they could copy or scan for me. Thank you joe k7mks _______________________________________________ TenTec mailing list TenTec@contesting.c
Would like to by a good working PLL Major board or send my board for repair to a person familiar with these PLL boards. Is anyone parting or servicing a Paragon? Thanks joe k7mks ____________________
Allen: What is Gary's email adr or phone nr. Joie -- Original Message -- Oops. Gary's call sign is W0DVN (not DNV). I'm not really dyslexic...but, confess to carelessness with the keystrokes. Allen--
Bill: I also have a Corsair II. S/N 02519 and would be interested in any comments you may receive regarding your post. Thank you joe k7mks 425.747.5349 _______________________________________________
I've heard that factory soldering concerns, with PLL boards, may have been satisfactorily addressed somewhere in the 500-600 serial number range. Rumor or fact? S/N involved? Tnx. joe k7mks _________
Bruce" FYI Joe -- Original Message -- Phil Woods "Bio-Lube" is my go to lubricant for VFO repairs (and others). Amazing stuff. Rich K8UV _______________________________________________ TenTec mailing
I"m enjoying a late S/N (25xx), which is new to me, and am puzzled about the filters. The manual says there is a 2.4 KH filter (which may be a roofing type but was not called that in the 1980s) and m
Brian Check w/ TT I bought some from them a while back for my Paragon Same part. 73 joe 7mks -- Original Message -- I just got my Omni VI back from repair and the USPS didn't treat it so kindly. I am
Did Ten Tec make any performance improvements (ie soldered board conections, etc) in the later #586 PLL over the earlier #585 PLL's ? Thank you. joe k7mks ____________________________________________
Thanks Gary Joe -- Original Message -- I cant speak insider facts here but I have had many Paragon 2 radios and none of them had PLL issues. Gary _______________________________________________ TenTe