- 1. Re: [TenTec] Inrad audio mod details (Omni 6)? (score: 1)
- Author: "Keith Flint" <kcflint@wirelessbeehive.com>
- Date: Mon, 23 May 2011 12:28:05 -0700
- This mod requires you to replace three components, all SMD chips with either new SMD chips (Two Capacitors and one resistor) or replace them with discrete (old type)capacitors and resistors. AMRAD su
- /archives//html/TenTec/2011-05/msg00178.html (8,503 bytes)
- 2. Re: [TenTec] Relay Chatter in Omni VI+ (score: 1)
- Author: "Keith Flint" <kcflint@wirelessbeehive.com>
- Date: Mon, 23 May 2011 12:29:44 -0700
- Check out your DC supply voltage first, sounds like it is quite low. Keith W7ZAC I recently purchased a near mint Omni VI+ and have used it on 40M and 160M without a problem. When I push the button f
- /archives//html/TenTec/2011-05/msg00179.html (8,295 bytes)
- 3. [TenTec] Model 302 Encoder/Keypad (score: 1)
- Author: "Keith Flint" <kcflint@wirelessbeehive.com>
- Date: Mon, 24 Jan 2011 13:33:09 -0800
- I have a remote Encoder/Keypad model 302 that is acting up. Ten-Tec says it is not economical to repair. It will not increment the frequency dial on my Jupiter 538 properly, the digits flash in the .
- /archives//html/TenTec/2011-01/msg00531.html (7,611 bytes)
- 4. Re: [TenTec] Argonaut V-Jupiter-Signalink USB and Digital (score: 1)
- Author: "Keith Flint" <kcflint@wirelessbeehive.com>
- Date: Mon, 20 Dec 2010 14:26:38 -0800
- How did you connect the SignaLink to your Jupiter? I am using one, and it works fine, and I use the Accessory Jack on the rear panel. I think I remember changing a jumper inside the SignaLink. If you
- /archives//html/TenTec/2010-12/msg00445.html (11,841 bytes)
- 5. [TenTec] For Sale or Trade (score: 1)
- Author: "Keith Flint" <kcflint@wirelessbeehive.com>
- Date: Sun, 21 Nov 2010 15:50:07 -0800
- For Sale or Trade Ten-Tec Omni-D Transceiver Model 546 Series B 100 Watts out 1600 thru 10 Meters including the 30M. and 12 M (aux position) Bands CW and SSB In Good Condition. Digital Readout is a b
- /archives//html/TenTec/2010-11/msg00324.html (7,354 bytes)
- 6. [TenTec] QSK Mod for Herculese II and Jupiter (score: 1)
- Author: "Keith" <kcflint@wirelessbeehive.com>
- Date: Wed, 16 Sep 2009 07:47:17 -0700
- Hi I will be acquiring a used Herc. II soon and I hear there is a simple mod. to make the qsk line from the Jupiter work with it. Anyone know how to do it? Thanks Keith W7ZAC
- /archives//html/TenTec/2009-09/msg00145.html (6,844 bytes)
- 7. Re: [TenTec] Jupiter update with CW (score: 1)
- Author: "KCFlint - WirelessBeehive" <kcflint@wirelessbeehive.com>
- Date: Wed, 24 Sep 2008 10:56:23 -0700
- Where do you grab the PLD Upgrade? It is not listed under the downloads on the TenTec downloads page. W7ZAC The chip upgrade is very simple. First, do the PLD upgrade as described on the Ten Tec web
- /archives//html/TenTec/2008-09/msg00303.html (10,084 bytes)
- 8. Re: [TenTec] Jupiter update with CW (score: 1)
- Author: "KCFlint - WirelessBeehive" <kcflint@wirelessbeehive.com>
- Date: Wed, 24 Sep 2008 10:57:30 -0700
- They charge labor and shipping for this, so it is not an option for me. W7ZAC It seems to me that a trip/shipment to Ten Tec for them to do the upgrade may be the wiser path. Just an observation.....
- /archives//html/TenTec/2008-09/msg00304.html (10,879 bytes)
- 9. [TenTec] New CW Personality Module Info. (score: 1)
- Author: "KCFlint - WirelessBeehive" <kcflint@wirelessbeehive.com>
- Date: Thu, 25 Sep 2008 06:30:39 -0700
- Hi. FYI The cost of the firmware chip is $50.00 plus shipping from Ten-Tec. When you download and install the new firmware installation file with the .exe extension, and run it, it will put a c:/prog
- /archives//html/TenTec/2008-09/msg00321.html (7,391 bytes)
This search system is powered by
Namazu