This conversation reminds me of my late Granddaddy who would tell me, Mike, don't borrow trouble. 73, Mike N4NT _______________________________________________ TenTec mailing list TenTec@contesting.c
Don, you are correct. I added the 17 meter crystal and the transmitted "spur" was about two watts, key up. Spoke with then technician Garland Jenkins about fixing it. He suggested if I wanted to work
Apparently Barry, it wasn't. Re: [TenTec] question about the omni c #546 It included everything for operation on 12 & 17 except the xtals. The 10 meter xtal was included. Sent from my mobile device.
Hi Pat, Speaking only from my dim memory of my 444 amp as it was before it caught fire, was successfully repaired at Ten-Tec and returned with their note that it was the last time a 444 would darken
If the IF's center frequency is 9.0 MHz and your filter was centered at 9.0 MHz, then you would hear the bottom half of the audio from both sidebands at the same time, I'd think. If you wanted to wor
But on reflection, with an SSB signal, you'd just hear one or the other sidebands but only the bottom 1.2 kHz of the audio spectrum would fall within the 2.4 kHz filter centered on 9.0 MHz. With CW,
Roger, I replaced my 4-pole SSB filter with the Ten-Tec model 220, 8-pole SSB filter. Of all the things I ever did to that rig, replacing that filter was the very best investment I made. It made the
I bought a number of these speakers from Jameco several years ago and installed several in Ten-Tec rigs. They fit perfectly and are stouter speakers than the original. You can tell by the magnet stru
Sorry. After getting out my magnifier I see that the speaker number I used was the 99995 AND NOT THE 99996. I cannot vouch for the 99996. Sorry for the confusion. 73, Mike N4NT I bought a number of t
OK. Here's the skinny on the Jameco speakers, straight from a Jameco rep's mouth. The model 99995 which I purchased six of back in 2003 has been replaced by the Jameco model 99996. The only differenc
I think I put one in the Corsair II but I've since lost it and cannot tell you. The new speaker with the other rigs I mentioned mounts inside the cabinet and the mounting holes mate up with the screw
Suggest you look in your supply at the speaker and take its measurements. Then I'd go to that Jameco site and find one that fits. You can go other places, perhaps but I do know the quality of the spe
Does anyone know for sure if "John Occhipinti" is a Michael Bloomberg alias? I would respectfully suggest, Mister Mayor, that if you wish to have a different type net, you start another instead of ch
I suspect that others can advise you about grease that will survive better over time. I used Phil Woods bicycle grease once, but after several years it became a bit gummy. 73, Mike N4NT Hello, Probab
Thinning out spares I'll never need, I find one pristine front panel for an Omni-B. It does not have the plastic Ten-Tec emblem for the white place at bottom, center-left. It never had that. Don't th
I've seen the thread about hot versus not so hot soldering irons and will relate my experience in specific terms: I use Weller soldering irons, they are blue and the tip can be replaced. I've used th
My Wellers are the models WP-40 and WP-25. My 'screwdriver tip' on the WP-25 is probably 1/32 across the rounded tip. Mike -N4NT- I've seen the thread about hot versus not so hot soldering irons and
When was your last post about radios by TenTec? Perhaps it would be better if you would delete the posts you find objectionable instead of criticizing posts of others. 73, Mike N4NT When did this bec
Hi Kevin, Your information about the Omni-C blanker was not true for mine. I have a Triton 544 and an Omni-C, each with the proper Ten-Tec blanker. The 544's blanker would quieten the loudest of line
Several years ago, having been driven nuts by power line noise and having found the cures, I wrote a summary. You can find it at http://www3.telus.net/ve7tk/POWER_Line_RFI.pdf One of the trickiest wa