I will be at the Dayton Hamfest in booth 227. Stop by and say hello. 73, Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 _______________________________________________ TenTec m
My N4PY Orion software provides over 25 different functions that can be done with the 302 remote tuning pod. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message
www.keyspan.com has a 4 port USB to serial converter. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "George" <goofyham@highstream.net> To: "Discus
Actually there is an ALC even for the transverter output. It stabilizes the drive in SSB and CW so that the output is limited and can't go beyond the set value. There is no connection provided to con
The ALC light is very important in SSB in transverter mode. It means the SSB envelope is reaching the drive level set by the power control and that the mic gain control is set high enough. The ALC li
Is this the noise that is eliminated when you add just a little hang time to the AGC? Set the AGC hang time to at least 0.12 and see if the rasp goes away. Carl Moreschi N4PY 121 Little Bell Drive Be
Boy, I knew the ham population was getting older, but I didn't realize it had gotten to this point. ; > ) Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message --
Under program control, using my N4PY control program, squelch works in all modes. And my program can handle the transverters very well including automatically reducing power to the transverter drive
I misread the topic. My comments refer to using the Omni VII with my program, not Omni VI. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Carl Mor
Both my Omni VII and Orion were used at field day. Each radio made about 1000 QSO's. They both performed flawlessly and handled the excessive QRM beautifully. 80 percent of our QSO's were made on CW.
The locut and hicut controls are really for SSB and not CW. They move the passband just on one side of the passband, where as PBT moves both sides in the same direction. When you move the hicut contr
Both the Orion and Omni VII were used directly in local mode. There was no ethernet connection to the Omni VII. We used CT for all our field day logging. Carl Moreschi N4PY 121 Little Bell Drive Bell
I have been running the exact combination for some time. The 8 watts out of the transverter will drive the ACOM 1000 to 200 watts, a pretty good 6 meter signal. And if you combine this with my N4PY s
No, the transverter output on the back of the Orion and Orion II is a very low level milliwatt output. It is not sufficient to drive the 1209. Also, my software and the N3FJP logging program work ver
The resets for the V.9 chip were required when people did not follow the correct procedure to initialize the band register values. There was a setup step that was missed by several people at installa
It does not have one. It uses its own proprietary serial interface. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "John" <fraz1@bellsouth.net> To:
It runs at 57,600 baud. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "John" <fraz1@bellsouth.net> To: "Discussion of Ten-Tec Equipment" <tentec@c
Don't overlook the possibility that the Trition was protected from reverse polarity by a reverse diode across the 12 volt supply connection. If this is the case, the diode would most likely now be sh
I just released version 2.37 of my N4PY Omni VII program. This version adds in the new features that Tentec has just added to the Omni VII. TRIP and RIP compression are now in the program. And RIP is
You can also just get a 4 port USB to serial converter. www.keyspan.com has one with four serial ports. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- Fr