The battery may be bad. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com Ever since I bought my Omni V.9, it had an intermittent frequency display. It would quit working, and then I
John Henry does monitor this list. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com After surviving more than forty years in some of the best and worst economic times, I'm certain t
The new rx366 board is simply a replacement board for the existing sub-receiver board. It is a very easy field replacement. It will require the new orion version 3 firmware. There are 3 roofing filte
That's the new firmware that will have the rx366 support. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com kenb, ky5g _______________________________________________ TenTec mailing
My N4PY software can use a Perseus, Flex, or SDR-IQ radio as a panadapter with the Omni VII. The IF on the Omni VII is not compatible with LP-Pan. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 2863
My N4PY software has full CW keyboard support for both these radios. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com Any ideas anyone. de Denton WB7TDG ____________________________
My software can still be run and control can still be done entirely form the radio. In this way, just the CW keyboard of my software can be used. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635
But you cannot do this with the Omni VII or Orion or Orion II. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com You can't control the functions of the radio by any means, but you ca
A tenth of an amp is all it takes to kill. But it takes volts to make the push to make the amps. In some scenarios, it is possible for 120 volts to cause the tenth of an amp to flow to kill. Carl Mor
The real question is is the filter 200 hertz off or is your impression of the same tone 200 hertz off. Only the 250 filter would be narrow enough for this to show up. You need a second radio to see i
The Omni VI has a 9 mhz IF. It would need a hardware mod to bring the 9 mhz IF out to LPPan. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com Has anyone come up with a clean way to
My N4PY Orion software will do this operation and use either PowerSDR-IF for the panadapter or TRX-Pan for the panadapter. You will also need the Telespost LP-Pan device to convert the 9 mhz IF outpu
I have just a few more comments on this. First, I have several users running the Orion with the 9 mhz IF mod, LP-Pan, and TRX-Pan. This works quite well and is very stable. Second, I also have an int
The Flex 1500 might be a better way to go then if sharing antennas. There's no hash with that one and still no sound card required or 9 mhz IF mod required. Carl Moreschi N4PY 121 Little Bell Dr. Hay
The transverter output level on the Orion is controlled by the Orion drive level. You can reduce the Orion drive to match what the transverter needs. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 2
Use at least 3 digits when you set RIT. Use *RMR050Cr for 50 hertz of RIT. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com On 6/3/2011 3:10 PM, Barry N1EU wrote: For those of you w
The internal BFO frequency adjustment for LSB is off 250 hertz. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com Switching between my Orion II and Omni VI+ using an Alpha Delta swit
They use a very fast reed relay for QSK switching/ Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com I was under the impression that Ten Tec qsk used pin diodes for switching, but I
The N4PY program sets the baud rate itself, so that is not an issue. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com I do not have a Pegasus, but that often resolves issue I see wi
The baud rate is not an option with any of the tentec radios. The N4PY program always sets the correct rate. You were using a kenwood radio last week which does have baud rate settings in the N4PY pr