Sorry. Make that reactance instead of resistance. 73, Alan N5NA Is not the resistance dependant on the wire material (copper or other), cross section (gauge) and length, and not dependant on the core
I put a speaker from an MFJ ClearTone speaker in my 961 a couple of years ago. I didn't need to replace the speaker, I just liked the sound of the ClearTone speaker. As I recall it wasn't a perfect f
Yellow = Yaesu http://www.heilsound.com/amateur/ad-1.htm 73, Alan N5NA My Proset Plus has a yellow sleeve on the cable that terminates in an 8 pin mic connector. Does anyone know what the yellow slee
Gary, I use only Mode B and can't tell any difference between 1.371 & 1.372. I think 1.371 and before was only Mode B. In fact, I can't tell any difference between Mode A & Mode B in 1.372. I usually
Me three. Right after loading 1.372 I rotated the BW control and completely lost audio. I had to turn the rig off and back on to recover it. I then did the memory clear routine and a master reset. I
Chuck, I bought my Orion in May, 2003. Unfortunately in June, 2003, I had to ship it in for repair of lightning damage. The repair invoice showed "Updated keyer/headphone board. Updated LCD display p
Since Ten Tec takes the previous firmware version off the site when a new one comes out is there any problem if someone hosts the previous versions for download? I was looking in my download folder.
Bob, Check here: http://www.n5na.net/orion/ 73, Alan N5NA Please send them to me! Bob W2WG Since Ten Tec takes the previous firmware version off the site when a new one comes out is there any problem
Already is one: http://lists.contesting.com/mailman/listinfo/orion Also on Yahoo: http://groups.yahoo.com/group/orion565/ 73, Alan N5NA doc wrote: BTW: Is ther any chance of creating separate TenTec-
You're missing half the fun! You can always go back to 1.349 if you don't like the newer versions. If you don't have 1.349 to go back to you can download it at http://www.n5na.net/orion. 73 & Merry C
Paul, I believe the Orion keyer is a mode b keyer. I don't think there is any way to change it to mode a. 73, Alan N5NA Is there any way to change the Iambic keyer from A to B, or B to A? I just got
Eric, Your post was not wasted! I learned something I had overlooked in the manual. I had wondered how to get the keypad to work on VFO B. Thanks! Alan N5NA Reading this, I think I did not understand
With all the TT705 mic discussion I pulled my instruction sheet out to see just what it has to say. "The Model 705 incorporates a momentary type Push-To-Talk (PTT) button (gray), a Push-On, Push-Off
Ed, K1NU's interface will work for this. You can take a look at it here: http://k1nu.home.comcast.net/k1nu/Products/index.html You just need to be sure whatever program you use it with will let you t
Bob, I think the default filter width gets set the first time you set a BW for a particular mode after a reset of the rig. At least that is my observation. As far as software is concerned...I am a Wr
Bob, There is mention of it in the firmware revision history. 08/25/03 Version 1.359 - Added bandwidth/mode association. Mode auto recalls last used BW. I think my previous statement is not quite rig
Is anyone using an Orion with a Kam+? I picked up a Kam+ last week with the intention of trying out Winlink using Pactor but I'm not getting enough AFSK out of the Kam+ to properly drive the Orion. I
Never mind. I found a jumper to change which will increase the output to a higher range for the adjustment pot. Working fine now. 73, Alan N5NA the AFSK
Bob, I think you need to give INRAD a call because they must have made a mistake. Their web site shows the 762 for $80. 73, Alan N5NA contemplating filters