Ifor one really enjoyed Mike's video and the points that he made onhis decision to purchase Ten Tec because of being a receiveraficionado. Hemade some arguments for the Low noise, easy on your ears a
I had to replace a set of drivers in an Orion a couple years ago and used these: https://www.ebay.com/itm/2SC1945-MATCHED-PAIR-2SC3133-2SC2509-ELEFLOW-HF-RF-TRANSISTOR-/282265736186I actually talked
Have a board that has been worked on one to many times. Probably has some bad parts as well but several traces are messed up. any one have a board that is in better shape? Don't care if it has the la
Bob, Thank you for the follow up. Just to clarify my test of the Hardware noise blanker. I was tuning above and below a strong station with blanker On. Before what was happening was the strong statio
Update: Problem NOT solved with the firmware update. So I went through the wiki and found the excellent information on calibrating the tcxo so that the sidebands are equal. TCXO Calibration Procedure
I have 2 Orion's 565 and 566. Both have the latest firmware updates V3. The 566 has the rx366 sub rx. The Orion has the standard sub rx. The Hardware noise blanker on the Orion works great. On the Or
Gary, Thanks for the followup. I know you have more experience on the Orion's than Me. So I had already tried both reset process'. Playing with it today with Field day going on so lots of activity. S
Issue solved, (I think) So trying the suggestions I did a full Firmware update or reinstall. Seemed like that DID NOT solve issue. So per discussion on the Yahoo group I did downgrade to 3.026 Versio
Wes,I play with a lot of the software programs and they all seem to have the latency issue. Then I added Carl's N4PY Orion Control software. As Carl said this solves the latency issue. I really like
Have two Orion's one super bright backlight the other not so much. Both start up fine and look good once going but one is for sure not as bright. So swapped the A9 boards thinking cap problem. makes
two Orion's One bright backlight one not that bright by comparison. both start the same and look good once up and going. but darker back light is always darker. So thought A9 board. so to test swappe
Gary,Checked the website you listed. I am not following what you mean by illuminator. I see the LED CCFL replacement kits as well as CCFL replacements.... Is that what you are talking about? Jon
https://www.youtube.com/watch?v=UnTHM23DLpk You might be helped by this very good video, troubleshooting an eagle with no output. It takes a very good step by step approach and solves the problem in
To our super techs on the list, I just picked up a Herc 2 and see that it can auto band switch if connected to a Corsair 1. However on the C2 Ten Tec dropped the Linear connector from the rear panel.
Doug and Fred, Thanks for follow up comments. I looked at the manual again for the Hercules II and it lists the pin out to be controlled by the Omni/Corsair I series of radios. Those that have the ex
Barry, I have a Clifton labs amp that I was wanting to install in my Corsair 2 9mhz IF for a panadapter. Not to steal your thread but do you have any thoughts as to where you would pull the IF out on
Hope some of the good troubleshooters on here can point me in a direction. I have a Corsair 2 that is very weak on receive. I have checked transistor voltages on IF/AF board 80984, the Osc/mixer boar
Ok I tried the rx switch clean, I had already done that a few times but did a bunch more slides. No change. As far as the filters. I am looking at the 9mhz 2.4 It is a soldered on filter? everything
Ok I tried the rx switch clean, I had already done that a few times but did a bunch more slides. No change. As far as the filters. I am looking at the 9mhz 2.4 It is a soldered on filter? everything
Ok I tried the rx switch clean, I had already done that a few times but did a bunch more slides. No change. As far as the filters. I am looking at the 9mhz 2.4 It is a soldered on filter? everything