Yes, provided that: - The ORION or ORION II at least has the A9-board upgrade - The memory backup battery was replaced within the last 2 yrs - Owner learns to use AGC and RF gain (never set it at 100
Did you do any Master reset or any other such that your sidetone is back to a default value, 200Hz off from what you are used to listen and tune too? Check SPOT value. 73 Mark, PA5MW When running dur
Hi, Situation: TT565 (ORION) connected via Microham Microkeyer MKII to PC running N1MM+ Both VFOA/VFO B freq are shown in N1MM and bandmap correctly Issue: 1) Callsign window of N1MM shows error mess
Not feeling offended at all.. :) Good Luck ! 73 Mark, PA5MW Now, there is an owner that is committed 100% to "Let's Make Things Better" (sorry Philips guys, had to steal that for this post)..... Mike
Nice ! I work for Philips as of 2000 only :) Although our department was recently sold to GIBSON Brands. We are now GIBSON INNOVATIONS. Small world :) Greetings from Eindhoven ! 73 Mark, PA5MW ah, sm
An RX-366? Where can I find this Gary? 73 Mark, PA5MW --Original Message-- From: terry foskey via TenTec Sent: Thursday, December 03, 2015 12:35 AM To: TenTec@contesting.com Cc: terry foskey Subject:
Since no RX366 turns up anywhere, I will do the INRAD #902 46Mhz 6-pole upgrade to my Orion or Orion II (cannot decide yetwhich is best on 160m) original 2nd receiver Anyone interested? 73 Mark, PA5M
I might add to that: Choose any equal length for your open dipole which a) suits your local environment at fysical lengths and b) produces the 3D radiation field you need for the required bands Note:
Hi Sinisa, On below picture I believe you will find both (on both sides of the pcb) https://www.flickr.com/photos/pa5mw/11384551726/in/album-72157638923217645/ The album is for public view , and you
If below pics do not help I can shoot some new ones, as I still have to upgrade my own TT565. Might as well be now. 73 Mark, PA5MW Hi Sinisa, On below picture I believe you will find both (on both si
Hi Mark, You first need to determine what your actual goal is here. Most IF filters are designed to create proper selectivity, matching the mode and current way of operating and signals on the band.
Check pictures 2,3,4,5,and 7 at https://www.flickr.com/photos/pa5mw/sets/72157640001358005/ There was no cutting done on the cabinet I used short pieces of 1mm copper wire, soldered in the power pole
Good day, And, despite being flat as a pancake, our Mickey-Mouse-country has 50+ free sites to offer? Which all have the same distance to the Northsea? Hmmmmm..... ;) 73 Mark, PA5MW I think this topi
**NOT happy with this. For more than a year I'm saving for the 1000 dollars needed to buy the RX366 here in EU. I'm almost there.....or make that was... I understand it is not available right now, bu
The tricky part is soldering the correct length of the copper wire crimped-soldered to the the PP inner part and implement that soldered end on the board at the exact length, so the outer PP connecto
Dear, We have been discussing the ORION III within our contest team and clubstation (2x 565+1x 566) for some time now. We would like to express our vision, but divided it in separate main areas so ot
Dear, We have been discussing the ORION III within our contest team and clubstation (2x 565+1x 566) for some time now. We would like to express our vision, but divided it in separate main areas so ot
Using Tmate2 here with my Perseus SDR, works great. Finally decent control knobs and a large VFO dial. All metal. 73 Mark, PA5MW Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com
Hello Rick, I am a team-member of 2014 IG9Y. In 2013 IG9Y participated in the CQWW SSB and is currently #6 in the MM section worldwide, just behind K3LR but in front of DR1A, W3LPL, II9P etc. That re