mouser has a speaker 60mm sq. no.25sp105 for 3.71 www.mouser.com ....I'm asking one more time if anyone knows of a replacement speaker for the Jupiter. I called the service department at Ten Tec and
I told you where you can get one. It is true you can often substitute a 4 or 8 ohm speaker, if the driving amplifier has enough power to drive 4 ohms. You can make a test with a resistor to see if th
WILL IT WORK ON A OMNI V http://www.n4yg.com/Corsair.html *We have used several of this Gentleman's products. Click on Link Above* * 73 from Wade/KJ4WS* I am thinking of installing a DDS in my Corsai
I have the top for the orion. If anyone has or gets wind of an unrepairable 565 or 566, I can use the enclosure snd some of the mon electrical bits inside. This to complete the hamfest basket case 56
The orion has been out for years . Did it take all these years for Kenwood to catch up. . . . and I think the "terrible time" Paul mentions after the Orion came out had more to do with TT managing ex
yes pull the ring off OK, finally got the new Omni VII that I've been waiting for. Alas, in the first few hours of learning how to use it, one of the knobs (PBT/BW) fell off! I believe the setscrew m
No more hamfest , I won't be going to Tenn. anymore. I have going there for 6 years. 73 Rod To avoid the NE snowstorm, I traveled south to Tennessee a day early last week. I visited the new Ten Tec f
book say's push the mnu button for 2 sec. red light comes on.vfo is lock Hi all Was playing with my Omni 7 this am trying to find some kind of vfo lockI keep bumping the vfo knob and going off feq a
I have these for sale mrf497, 29c-1971, 2sc2630 --Original Message-- From: Al Gulseth Sent: Friday, October 31, 2014 11:39 AM To: tentec@contesting.com Cc: Bwana Bob Subject: Re: [TenTec] repairs It
M y Dad used a 40m double extended Zepp for years so did most of the Hams he talked too. I use a 80m double extended Zepp up 70ft. works great on 160,80,40,20,15, 10 meters Indeed the Zepp antenna us
My Ten-Tec 238 tune my 80 double ext.zepp on all bands 160-10 with a 4-1 balun 182 ft of 400 ladder line then the 4-1 with 20ft of coax. Because the MFJ 929 tuner only has unbalanced outputs thus no
My antenna must be working I get great reports from hams, they think I am running power but only a Orion. 100w --Original Message-- From: JAMES HANLON Sent: Monday, September 15, 2014 9:48 PM To: ten
Thats what I got a double extended 80 zepp 166ft each side of center up 70ft. works great. Here you go..... Didn't know I'd start such a discussion. Bob has what I understand and have understood thro
put it in your amp only turn on the filament and let it run for 5 or 6 hours until you turn on plate voltage. I know a ham that had 34 304tl tubes and that what he did. y --Original Message-- From: A
RF PARTS suggest that you do that. There is no way to do this with the AL-80B. A tube such as the 3-500 does not need any "burn in" time. 73 Bob, K4TAX -- Original Message -- From: "Rodney" <w3krq@de
A know a ham you got two used 3-500z he put them in his amp after about 5 minutes the one tube shorted took out the bias circuit. If it were an external anode tube with a indirectly heated cathode a