Search String: Display: Description: Sort:

Results:

References: [ +from:w5pny@w5pny.com: 10 ]

Total 10 documents matching your query.

1. [TenTec] Orion II and Ameritron QSK-5 and 811H (score: 1)
Author: "Harry G. McGavran Jr. " <w5pny@w5pny.com>
Date: Wed, 10 Jan 2007 11:47:54 -0700
I have a brand new Orion II I am trying to hook up for QSK CW using my Ameritron 811H and Ameritron QSK-5. On the Ten-Tec web site is the following description of how to hook up a QSK-5: == Ameritron
/archives//html/TenTec/2007-01/msg00259.html (9,247 bytes)

2. Re: [TenTec] Orion II and Ameritron QSK-5 and 811H (score: 1)
Author: "Harry G. McGavran Jr. " <w5pny@w5pny.com>
Date: Thu, 11 Jan 2007 11:02:07 -0700
. . . This was finally resolved by placing a 1N4001 diode in series in the line from the QSK-5 AUX/KEY-1 to the Orion TX EN. The cathode of the diode is on the QSK-5 AUX/KEY-1 side and the anode is o
/archives//html/TenTec/2007-01/msg00286.html (8,414 bytes)

3. [TenTec] Centering Orion II Roofing Filters (score: 1)
Author: "Harry G. McGavran Jr. " <w5pny@w5pny.com>
Date: Tue, 16 Oct 2007 11:01:30 -0600
It seems that one really needs a stable steady signal, both in frequency and level to do this job. Short of homebrewing a crystal calibrator (since these seem to be few are far between these days, ev
/archives//html/TenTec/2007-10/msg00337.html (8,050 bytes)

4. Re: [TenTec] Centering Orion II Roofing Filters (score: 1)
Author: "Harry G. McGavran Jr. " <w5pny@w5pny.com>
Date: Tue, 16 Oct 2007 21:10:44 -0600
Thanks to everyone for all the suggestions. The Elecraft XG2 looks like a good thing to have in any case, so I think I will get one. 73 -- Harry, W5PNY -- Harry G. McGavran, Jr. E-mail: w5pny@arrl.ne
/archives//html/TenTec/2007-10/msg00345.html (7,811 bytes)

5. Re: [TenTec] Orion 2 Firmware 2.043B Released (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Fri, 04 Jun 2010 09:36:58 -0600
For me, there are two problems with 2.043B, one affects me in only a minor way, the other is a major nuisance. I live in a rural area where I rarely need NB or NR, so the minor nuisance is the way NR
/archives//html/TenTec/2010-06/msg00059.html (9,936 bytes)

6. Re: [TenTec] RX366 9 mhz Output (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Mon, 12 Mar 2012 09:31:45 -0600
I'm using it with an Elecraft P3. I'm using a Z10000B 15 db preamp between the 9 Mhz RX366 output and the P3. The gain from that is just fine, but it even more gain would put it closer to what peopl
/archives//html/TenTec/2012-03/msg00110.html (7,662 bytes)

7. Re: [TenTec] RX366 9 mhz Output (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Mon, 12 Mar 2012 10:33:40 -0600
The display when transmitting seems to be at least 30 or 40 db higher than when receiving. If one changes the offset to accommodate this, I don't notice much if any distortion, but there are spikes (
/archives//html/TenTec/2012-03/msg00117.html (8,921 bytes)

8. Re: [TenTec] 566 Orion II Firmware Version V3.029 ---Comments (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Sat, 14 Apr 2012 20:31:25 -0600
for >LSB. It reads low for CW and depends on whether the mode is UCW or The spectrum display for both my Orion II's is around 400 cycles low for both LCW and UCW with both 3.028 and 3.029. Also, the
/archives//html/TenTec/2012-04/msg00190.html (8,681 bytes)

9. Re: [TenTec] Orion 565 V3.032x7b released (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Thu, 07 May 2015 10:49:58 -0600
This is really really great news! Since I have an Orion II, I've been on 3.029 ever since 3.033xd came out, since while I really like the S-Meter table, I can't stand the loss of the S-Meter followin
/archives//html/TenTec/2015-05/msg00023.html (7,255 bytes)

10. [TenTec] New Orion II Firmware (score: 1)
Author: Harry G McGavran Jr <w5pny@w5pny.com>
Date: Fri, 15 Jan 2016 18:24:14 -0700
I can't believe that others haven't noticed yet... On the new tentec site (http://www.tentec.com) a new page went up today with a link to new firmware for the Orion II -- 3.033xe. This firmware has t
/archives//html/TenTec/2016-01/msg00323.html (7,927 bytes)

Current List: 1 - 10
Page: [1]
This search system is powered by Namazu