TenTec is pricing their used 253 at $750.. Dave W7DPW Condition is a 9. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/l
I had no idea what RUFZ was until I Googled and found: http://je1cka.jzap.com/rufz-mirror/xedtr.htm Dave W7DPW fast as that was _______________________________________________ TenTec mailing list Ten
My 253 is becoming very noisy when the roller is moving and binds up rather easily. What lubricat is used on the roller coil and bearing surfaces ? I had this information some time ago, but seems lik
However, once the 253 is adjusted for proper match, it just clicks once when you turn it back on. If you are on the same antenna antenna and frequency. It remembers where is was last set. But,,, if i
Dave, 253 Arrived this evening. I pulled it out of the shipping box and it looks great. I'll test it on line later. It looks exactly like my other 253, they are both in pristine condition, I did have
Is there any consensus of the roofing filters for the Orion. I remember some time back there was a disussion of INRAD filters, but I can't find them in the archives. Thanks, Dave W7DPW ______________
Don, I'de like to purchase. Dave W7DPW _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
We recently purchased a new Neptune washer and have had it for several weeks, I have noticed NO interferrence what so ever. I guess that I'll have to make a further check and let the list know.. dave
It looks like their home page is okay, but when selecting anything else, a number of error messages appear. dave W7DPW home _______________________________________________ TenTec mailing list TenTec@
There are three ways to do it. 1.) Get rid of the tranny and just use the resistor only, it should work. 2.) Use an NPN instead of the PNP tranny and wire as you mentioned, ground base, feed the emit
You will need a separate PTT .. dave W7DPW OMNI 6plus Owner basics 3) of a rear of which tone, Mark _______________________________________________ TenTec mailing list TenTec@contesting.com http://li
dAlso my using ALT-Ø216 sequence. Just hol down the Alt Key and press the zero, two, one ,six keys in sequence. Dave W7DPW _______________________________________________ TenTec mailing list T
I used an email to creat the slashed zero in this reply. Didn't you see the see the slashed zero ? Use the KeyPad with Num Lock On.... (OOps, I forgot that bit of info)... ATL-Ø216 = Ø
As I recall, Most Band Info is on the RS-232 pins.. Dave W7DPW Could way to grab after bandpass filters 'wire wrap' I would assist _______________________________________________ TenTec mailing list
If anyone has used the OMNI-D on RTTY I'de like to hear with them off line. Thanks, Dave W7DPW _______________________________________________ RTTY mailing list RTTY@contesting.com http://lists.conte
Ed, Thanks, off from For to _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Jerry, I have n OMNI-D and would like the mod for FSK.. I use this machine as backup for my OMNI 6 plus. Thanks very much. Dave W7DPW it suspect or this ______________________________________________
OMNI-D series output is 100 W (That's about 200 watts input) Dave W7DPW D series B? says 100W out and the other says 200W output. Which does it _______________________________________________ TenTec
The OMNI-D and the TT 243 VFO enables this Dual receive function. In fact, it offers a great many combination for Rx/Tx (6), even Crystal Control.. Dave W7DPW with two accessory of simultaneously. __
Of course, you'll be sendin the VI+ for repairs and keep as a back up ! David J Drew -- W7DPW Over 50 Years with Same Call for with _______________________________________________ TenTec mailing list