I set up my new to me Jupiter this afternoon and all was well... until I decided to hook it up with my Hercules II amplifier. I set the keying loop on on the Jup main menue and hooked to TX Out + TX
For those wishing to use a Hercules II with their Jupiter. A call to Gary, the Herc II guru, at Ten-Tec solved the issue I had with the Jupiter not keying the Herc II. It turns out that it is an issu
I began organizing all my radio equipment last weekend in it's new desk. I have discovered (gasp) that I don't have room for it all. Having a new Ten-Tec station as well I find the following excess t
Omni V.9, very good condition, full N4PY V.9 upgrade with new factory keys installed in the pad, all filters... 2.4, 1.8, 500 and 250. Plus the narrow filter slot (dual filters) 500 Hz. Radio has the
New.... sitting in box since November.... out of box only to upgrade firmware and mount fan kit. Made a couple contacts on 60, 40 and 20 to test it in my shack. Model 516 Ten-Tec Argonaut V516 with T
New.... sitting in box since November.... out of box only to upgrade firmware and mount fan kit. Made a couple contacts on 60, 40 and 20 to test it in my shack. Model 516 Ten-Tec Argonaut V516 with T
Have any of you with an Argonaut V that has the latest v 1.07 software noticed if your lsb and rit annunciators still light after the upgrade ? Mine works FB as usual but just noticed the lsb annunci
Well the 4th person already emailed me that they also have an anomoly with the LSB indicator and/or RIT indicator since the 1.07 upgrade. I assume there must be a "bug" in it. Whew.... I thought I wa
Whats the diff between these "New" HP 5840A's that hit eBay late last week and the ones you guys have beside size.... the ad (copy below) implies no computer is needed for set-up etc. ?? Mike, W9WIS
Now I know what I can do with that 650+/- feet of Andrew FSJ2-50 3/8" hardline I have had laying around for several years..... 5.96 dB at 1 GHz and 21.7 dB at 10 GHz per 100 feet (.97 dB at 30 MHz bt
When I upgrade to v1.07 it locks the band. Anyone else having this problem. I went back to 1.04 and all is well. I tried several times but always get a "bug". Mike -- Michael Melland, W9WIS Winneconn
Yep.... I finally thought of doing a reset too and all appears well. So 516 owners if it doesn't appear to "take" right away do a master reset and all is well... Mike
I thought I'd mention this here... although it might be old hat. Some on the Icom PCR-1000 list had mentioned this device and how great it was having a real knob on the software defined and controlle
They turn continuously..... and push down like a momentary switch. You can program turn to right, turn to left, short click down, long click down, click then turn right and click then turn left all
I'll take it.... pse advise. Mike Arrl 1968 "Hints and Kinks" , 128 pages, abt 9 1/2 by 7 in. A freebe . Just send a pre-addressed envelope with postage and I will mail it back to you. It goes to the
I use two RM-70 Astron amps in parallel to drive my Ten-Tec Hercules II amp. The amps have a post on the rear to enable them to be paired direct... regulator to regulator. It is not a true "sense" ci
will notch Goes to show that "different strokes for different folks" is sure true in the choice of radio gear. I have a full filtered Omni V.9 that I teamed up with a Timewave 59+. I hated the SSB a
Anyone else notice that the new ARRL QST review of trhe Argonaut V claims firmware version 1.06 ? Wonder what's new and when it's going to hit RF Squared. Or perhaps it was a typo in QST... Mike -- M
As for me, and I suspect I'm typical, I get great audio reports with my Omni V (V.9). I find my audio is best with the stock Ten-Tec 705 desk mic.... and I also use a Heil Pro Set with the HC-5 eleme