Don, "personal consumption"????? I didn't know they were to be eaten??? You guys in CA?????? I have a business, DSM Labs, where I service and restore certain radio equipment. Primary R 390, R 390A an
Hi Don, One thing I am setting up for, in particular, is logic board work for the Omni 6 and the Paragon series. I have built 4 test beds with special adapters that I fabricated to raise components a
Hi Lee, We have very similar interest indeed. I didn't get into the vintage side of my equipment in my last post. I have that equipment just for fun. I have an Hammarlund HQ 180 paired with a Johnson
Hi Allen, I would be interested in your pin diode work on the Omni VI. I have seen Omni 6 + here that had sensitivity down to .10uv and others that were close to .6 or .7.. Even that, .6, is decent b
Hi Barry, Good idea.. I will try to set up soon and make a recording, however, the limiting factor, is still how well our ears/brains can decipher/separate two weak signals in the same passband, choo
Barry, I meant to comment on the Ten Tec O6 audio you mentioned. I too ran a remote a pre DSPaudio line to the rear panel on one of my O6. I fed that into a combo preamp/amp I designed using a 6CW4 n
Hi Gary, Yes but the scope of my testing and interest thus far has been more about weak signals in a typical QRP sprint or simple weak signal work in the absence of contest conditions. The K3 or an O
the key to success with tapping the audio pre-dsp is to add some analog low pass filtering with a turn-over freq in the 3000-3500hz region and fairly steep roll off. The Omni 6 is just TOO hissy/nois
Hi Barry, This has been my experience as well. But having some decent equipment on hand allows me to confirm my hunches.. Hi I do appreciate your feedback. Have you heard anything about the DDS repla
No, I haven't Glenn and I'd also like to see more data. As far as I know, nobody has run the output of the DDS replacement through a spectrum analyzer. My concern is both phase noise and spurs. Hi Ba
They are both very decent.... I greatly prefer the Omni 7 audio over the K3. The K3 is a better with close in Dynamic range.. And if your looking for a sexy radio, just saying, that $10K Icom might b
Hi Jerry, Sorry you had a bad experience with Paul. He is a very talented and trustworthy man and a [ersonal friend.. Without going into any detail, I spoke to him at the TT fest and he has some pres
My Sincere apologies to Jerry and the list for a post that I made to this list. Jerry had expressed a concern and not thinking, I responded to this on list.. I did NOT mean to sling any mud or cause
Send request to address above for the revised list. Not sure what you are asking???? ( What are you saying????? ) I have built a large and growing inventory of all parts for the O6 and Paragon 1 and
Would copying the contents of a known good EPROM for a Omni VI, to a new EPROM and providing that to a person who owns an Omni VI in need of a new EPROM be a copyright violation? If that person owns
Hi Barry, Nice project and thanks for sharing it with us. 73. Glenn WA4AOS DSM Labs N4YG developed a nifty and elegant sine wave sidetone mod for the Corsair II. I posted all the info with Joe's appr
Wonder if Jerry would be interested in building some boards..Just a thought. Glenn WA4AOS DSM Labs N4YG developed a nifty and elegant sine wave sidetone mod for the Corsair II. I posted all the info
Barry, I wonder what software you are using for the Omni 6 to Log with. I sent an email to Carl and he said hi Icom package works with the Omni 6 and I may buy a copy. Presently, I have built an inte
Jerry, You did such an OUTSTANDING job on the Corsair Display project, I bet others would be very interested. We can only give you an A+++++ for the last project. You can put me down for 15 boards to
Hi Jerry, Yes, good point. Steve Hunt did indeed design the board and wrote the firmware for the PIC and certainly deserves a big gratitude of thanks for his design efforts to get that project off th