Sorry, wrong reflector.... I've been searching around the net and haven't found a single point of information. Has any one set up a 6700 in an SO2R environment? I'm interested in how to handle antenn
I have an Array Solutions 8x2 switch. It's the out door version but it's never been out doors. I have it mounted at the bulkhead in my shack. Included will be two integrated controllers. Pic's availa
The switch is sold. Thanks Rich - N5ZC $975 shipped to USA. Rich - N5ZC _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTal
I'm working on setting my station up as a 'glass panel' station. All of my equipment will be rack mounted and controlled via my pc, and a couple monitors including a touch screen monitor. Can anyone
I've been searching the net without much luck. Does anyone happen to know the bolt pattern dimensions of the Rohn 55g Beacon Plate. The bolt hole dimensions would also be helpful. Mine's at 140' whic
I have a triplexer and band pass filters from 4O3A. They work very well. Pics on my qrz.com page. You have to tune right on the harmonic to hear any noise. I may add some additional coax stubs to red
The entire system needs to be looked as well. I have the 4O3A triplexer good for 4500 watts, however, my stackmatches are only good for 3000 watts. Not issue for my station as its setup for so2r or p
You'll be fine with thimble to thimble. Rich - N5ZC and the same for coupling from the 11200 philly to the 5/16 using the same 1/2 thimbles... is this a possible issue? Do I need to use insulators in
I'm lucky, I have real Great Horn Owl's and Hawk's that hang out on the boom's of the yagi's on my towers. I don't have a bird issue. Rich Good luck, 73 Joe K2UF --Original Message-- From: TowerTalk
I've been searching the net looking for definitions of exposure B and C without much luck. I thought I read some where that exposure C is used for a tower that is in the wide open with no structures
Jim, The tower is out in the middle of the country and he does not have a traditional shack. The steel valve box is the shack/equipment room, which happens to be made out of steel, that he's trying t
I have a Stack Match in excellent condition. It's been in service for just over a year, no longer needed. $225 shipped, USA only. Rich - N5ZC _______________________________________________ _________
I have a Stack Match in excellent condition. It's been in service for just over a year, no longer needed. $225 shipped, USA only. Rich - N5ZC _______________________________________________ _________
The Stack Match has been sold. Thanks for the inquiries. Rich - N5ZC $225 shipped, USA only. Rich - N5ZC _______________________________________________ ______________________________________________
Bryan, I had this very question last year when I was getting the parts together for my 140' rotating 55g tower. Gerald, K5GW, quickly set me straight. While more expensive I ordered and installed the
I'm looking at a 7&10-30LP8 log periodic. After looking at the manual I don't think it's side mountable on a tower due to the phasing lines. If anyone has experience with this antenna I'd like to hea
Quick question. Is the MFJ series of SWR analyzer's the only ones susceptible to BC interference? Any issues with the Comet or RigExpert series? I know I can get a filter for the MFJ, but I don't nee
Thanks for all the information guys, W9PN lives few miles from me, he's having an issue with his MFJ-259 (pretty sure it's a 259). There are a couple broadcast antennas to his West and my North. One
I just tried DOSBox. Mastcal now runs, cool. Haven't been able to use it for a long time. Rich - N5ZC On 10/11/2016 2:13 PM, Kirk Kleinschmidt via TowerTalk wrote: Steve and the gang, Have you simply
Gary, The bucket/man lift makes installing antennas a piece of cake. I set the boom of the antenna on the rail of the bucket/man lift. You may want to tie it down with a rope for safety, I didn't. Yo