I was in the same situation. I reported the detail here last summer (frequency updating takes 5 ~ 20 seconds after the actual change, some time WL logged the QSO on wrong band because of the delay).
Just woke up and decided to play CQ 160 CW, updated to 10.30 the other day but first time to play with. As I have seen as "choppy cw" previously on this reflector, I am another victim of CW keying pr
That did it, thanks ! --Original Message-- From: writelog-admin@contesting.com [mailto:writelog-admin@contesting.com]On Behalf Of W. Wright, W5XD Sent: Saturday, January 26, 2002 7:10 PM To: k2qmf@ju
Seems bavarian-contest-club.de is not up ... This is the download page maintained by JE3MAS: http://plaza16.mbn.or.jp/~masiii/ Also Pileup by G4ZFE is another for practive mode http://www.babbage.dem
I don't know if it is just me, the feature is perfect but I have trouble in that particular font used. Especially I hate "E" that is so hard to distinguish with "K". Is there any way to change the fo
Hi Doug Radio Shack probably can cure your problem again. Most likely their clip-on ferrite core (available like $2 for 2 pcs ?) at PC end will solve unwanted RF generated from PC in the shack. 73 Jo
I am quite sure that the noise you are hearing is not due to RF feed back. Instead, you are hearing the sound blaster hiss noise (-100dB bellow audio peak level ? or better, depending on your PC hard
I made FSK keying circuit with a photo coupler using com port TXD and GND connection. I don't know how TS850 and TS870 are, but originally Kenwood FSK keying has been in backward compare to Yaesu/Ico
Make sure the concept for LSB and USB included. I guess too many people never used analog type rig (remember, calibrating LSB and USB individually), and keep on transmitting in 7,150~7,153 or 14,347~
If the KAM command is identical with KAM '98 (I believe so), then in order to put KAM back from hanging HOST mode - " S00 HOST MODE" to indicate you are in host mode press and hold [ALT], then type "
I could not read from your e-mail if you could get the frequency control to JST245 by WL before connection of CW keying or not. If not working at all from the beginning, check if your RS-232C cable i
Hi Doug I felt CQWWCW coming up, so I took my serial cable for JST-245D out and checked for its configuration for you, hi. Typical Null-Modem cable is made in RED cable and so obvious. Another altern
I tried to make WL work with W9XT card or KAM '98, but finally gave up. XT card was dragging Radio control (freq/mode up date too slow), and WL never setup KAM '98 (leaving in Host mode, KAM not resp
For the best to WL entry user, I suggest to put all know-how's known to the WL group into the initial writelog.ini file and "rem" them out. This should be much easier (just release "rem" one by one,
I had same problem with TS950SDX, when I used W9XT as voice keyer. Frequency update was every 5 ~ 15 seconds. When I switched band and made new QSO, it was logged in as wrong band in so many occasion
I am using TS950SDX and Heil headset. I think the basic should be same. "TREMENDOUS HUM" -- are you using any scheme to reduce the sound card SPEAKER OUTPUT level into the mic input ? Without this, t
Well, I have not try WL with KAM '98 since Ver. 10.12 (WL failed to find KAM and leaving KAM on freeze in terminal mode, and needed to reset by removing the Lithium battery every time when tried to s
I need another help other than KAM 98 issue sent previously, if you don't mind. With WL 1012, I can control TS950SDX (thru IF-232C) with no problem (frequency read out on WL about a QSO behind if I j
Well, I shouldn't be playing with PC during WPX contest but ... If you subscribe RTTY reflector, discussion on Turtle Beach Santa Cruz was going on as the best fitted card for RTTY decoding. When I u
I have mentioned Ron about the subject a couple years ago. I guess nothing happened and probably need more group opinion. So if you agree, please come and join to the discussion group. I am running W