Mike In the original you may not have those lines, you may have to add them here is a section of mine [Ports] COM1:=19200,n,8,1 COM2:=19200,n,8,1 COM5:=19200,n,8,1 COM7:=19200,n,8,1 CommSlot3=5 CommS
Hi Nick, when I set up my new computer, which had NO serial ports I faced that same problem. I am using an EdgePort/8 that is 8 COM ports from USB. Has it's own driver and works just fine. I use it f
Greg, In the Programs menu for Writelog V10 you should see a program called Sound board mixer control Run this before you bring up Writelog It will have all the choices you have in your computer for
Rick Take a look at Tools / SoundBoard Options and select the compression button. There are choices that are Mono and choices that are stereo. I suspect that will do it. I use MPEG-3 stereo 11KHz as
There is actuall a third choice. 3) Change the CI-V address in WL to that of the PRO or PRO II This is done with an .ini file entry, such as this cut from my file: [rigs] Icom IC-756PRO=0x6e The adva
Bill Have been using the setup for a long time so will offer some comments. many sound cards and their mixer screens have the capability to "Boost" the mic, that is, to switch in a preamp in the soun
Al, You certainly can use the Top Ten decoder in manual mode and therefore not need all the other "stuff". here I use the Top Ten, but hook it directly to the rig ( IC756PRO ) That way it tracks the
Eric I just took a look at one of my ocntest archive CDs These recorded entire contests, one CD for each position in a Multi Multi for the entire 48 Most and the largest file was 7.8 MB A few were sm
I have the Edgeport 8 port unit here and it works fine 4 port and 8 port are on eBay often, but new they are pricey Ric KV1W I have the F5U103 on XP and it works fine doing FSK. They are hard to find
Don Open the following: c:\Windows\WLOGKEY.INI With some OSs it may be c:\winnt\WLOGKEY.INI GL Ric KV1W I HAVE ACQUIRED ANOTHER COMPUTER WHICH I AM DEDICATION TO HAM RADIO. I HAVE INSTALLED WL INTO T
Clive, You didn't imagine it, it is there, or at least can be in the rigs section. See mine below: [rigs] IcomForceSplit=1 Icom IC-756PRO=0x5c Com5:=19200,n,8,1 Com7:=19200,n,8,1 It may be one of tho
Doug I just checked my 8 port Edgeport and all is well with the band maps it just doesn't make sense to me, that the Radio Button has the right freq and the band maps don't. I thought the same data w
Chuck I have been using Writelog for many years, much of them as a Multi-Multi, now back to SO2R The perspective I would offer is, if you want a static setup, get the product, have your setup arrange
Geoff I have had good success with Edgeport USB to serial boxes. Sometimes available on eBay, but pricy new. I am sure there are others that work and others can comment. I would ask why use two seria
John Take a look in the Packet Terminal section in the Help files. the to the COMM area of the Writelog.ini. Those parameters are set in the .ini file. Hope that helps Ric KV1W Hi, In preparing for t
Oops, That's the [PORTS] section in the .ini file Ric Hi, In preparing for this weekends WPX, I was working out how to connect packet to my laptop. It has a COM1 port, but I am not sure how to set th
Jim As I follow this thread, is it possible that the rig port on the 1K needs a particular state on the DTR to function properly ? And when you remove that and use it for CW, the now unused pin on th
My Word Windows XP Media shows COMxxx up to 256 Guess serial ports are here to stay, at least in some incarnation Ric KV1W Thanks to K5NA the problem has been resolved by going into control panel and
First, Why use a second port ? it is intended to use the RTS of the rig control port. Second, if you need to use other ports, you can set up in the .ini file. See the help for that. You basically tel
One word of CAUTION Writelog .ini entries ARE VERY CASE SENSITIVE It must be: CommSlot3=7 for example if you use lower case it won't be recognized or if all case it won't work etc Maybe that's the is