Hi Can some one tell me the size of the brearing balls of a Ham IV rotor. The manual doesn't say any thing on the size. I need to replace a few of them peter _________________________________________
Hi I do have here a big rotor but this nice thing hasn't a direction readout. Its possible to add a potmeter. Now I'am looking for a simple schematic for the readout. There are end switches to preven
Hi Is there a reseller or manufacture of a 4 square box for 80 meters here in Europe? Peter PC2A _______________________________________________ See: http://www.mscomputer.com for "Self Supporting To
Pitures are on http://www.pi4cc.nl/tips => Stubs Peter PC2A _______________________________________________ See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather Stations", a
Hi I have just received a second hand 40M3L antenna made by M2 There is an incomplete manual with it. Its contains 5 pages but at least there must a page 6 Can some one send me the essambly manual in
Hello Group Has any one a nec file for the 40M3L antenne bij M2? 73 peter PC2A _______________________________________________ _______________________________________________ TowerTalk mailing list T
Hi I'm looking for a manual of the 40m3l by M2 Pse the version with hairpin. Peter PC2A _______________________________________________ _______________________________________________ TowerTalk maili
Hi, What kind of rope do you guys to make a single tram lin? We tried a tram today for the first time and we got broken the tram line when lowering a beam The line was a 4 mm stainless steel . Peter
HI Have a look at http://www.pi4com.nl/160vert.htm Here we pull a 130 feet tower from horizontal to vertical bij hand. Thats me at picture number 2 10 years ago and helping PI4COM to get it right don
Hi Can an "open" dipole placed in this setup? peter PC2A john@kk9a.com schreef: _______________________________________________ _______________________________________________ TowerTalk mailing list
Hi In preparation to build a new 40 meter beam, I'am searching possibilities to make the matching C Normally in a smaller beam We using 2 different diameter of aluminum tube with an isolated tape bet
Hi Due problems with a new landlord I have for sale a all most finished home made full size 3 el 40 meter beam per description in ON4UN lowband dx-ing Prefer pick-up in The Netherlands. Pictures on r
Hi Can some one point me to info on how to build a 40 meter short 2 el yagi? 73 Peter PC2A/PI4CC _______________________________________________ _______________________________________________ TowerT
Hi I like to make a rotory dipole for 40 meter (full size) For constructions reasons I want to feed the the dipole with a gamma match. Nec4win says that the impedance will around 60.8 +j0.12 How can
Hi In teh QST of may 1998 and in the Lowband Dxing book there is a ice 3 el yagi by NZ3W I can't find any message from some one who build this antenna. I see 1 post with the same question. Has any on
Hi I have searched on the net for a home made stack match with a BIP/BOP switch. So far I found only the a top/bop/bottom switch combination. Can some one point me in the right direction. Peter PC2A
Hi We are just finished with building a 2 el yagi for 40 meter This is a 2 el full size dipole reflector on a 5 meter boom I got the information from ON4UN yagi programme When moving the beam up, qrg
Bob Gibson schreef: Bob Can you post a compilation of the post here on the reflector? I think a lot of people are interested in the information. Peter PC2A ___________________________________________
Gary "Joe" Mayfield schreef: Google is your friend!: http://www.qsl.net/w3pp/ Peter PC2A A bit smaller: www.pi4cc.nl _______________________________________________ __________________________________
Michael W5NIG schreef: We (PI4CC) has bas experience with this rotor. Within 5 years it hits the trash can. http://www.pi4cc.nl/bigboy/ Peter PC2A _______________________________________________ ____