I have an existing 25G tower base that is damaged and needs replacing. Two of the four existing bolts align to the new base - What experience and advice would the group offer regarding drilling the c
Tho I have not done so myself, I did a lot of research on this subject in the past for others, and the responses were all favorable. In fact, one source said that properly done the inserted bolt had
How about drilling the new base to match the bolts? If you are on a pier pin, the bolts dont do much anyway. WL _______________________________________________ _______________________________________
It's not clear what you are doing. If you're talking about a standard 25G self supporting base plate, where are the two bolts that don't line up? If they are inside the footprint of the new baseplate
If the bolts that are already there, are possibly welded internally, or fixed to internal anchoring metal within the cement, then wouldn't it be true to say that drilling out cement material and inse
The Simpson company has info on the hole size and depth to bore, the bolt size and epoxy to use. You could look in the phone book/internet for a local concrete boring company. They could do the job o
Author: K7LXC--- via TowerTalk <towertalk@contesting.com>
Date: Tue, 8 Mar 2016 15:41:43 -0500
Two of the four existing bolts align to the new base - What experience and advice would the group offer regarding drilling the concrete, inserting a bolt and epoxy it in ? Easy peasy. Just do what y
Jag har från och med 8:e mars inte längre tillgång till denna mejl pga en tjänsteresa. Om du försöker att anmäla dig till VII:e graden i Skara 13/3 så var sista anmälningsdatum söndagen 6/3. Jag komm
What is the correct epoxy please? Bill W2CQ On 3/8/2016 3:41 PM, K7LXC-- via TowerTalk wrote: I have an existing 25G tower base that is damaged and needs replacing. Two of the four existing bolts ali
Author: K7LXC--- via TowerTalk <towertalk@contesting.com>
Date: Tue, 8 Mar 2016 16:07:42 -0500
Go to your local hardware store and get some construction epoxy. They'll have a couple of choices in squeeze tubes. It's typically stronger than the concrete so just about any of them will be FB. Ch
Bill and all, My crank up is bolted to three 3/4" diameter lengths of all-thread held in place in 7/8" holes (prepared as specified by the manufacturer) using Simpson Strong Tie two part construction
Jag har från och med 8:e mars inte längre tillgång till denna mejl pga en tjänsteresa. Om du försöker att anmäla dig till VII:e graden i Skara 13/3 så var sista anmälningsdatum söndagen 6/3. Jag komm
Author: TexasRF--- via TowerTalk <towertalk@contesting.com>
Date: Tue, 8 Mar 2016 16:23:30 -0500
Am I the only one receiving these emails? Third one today. Gerald K5GW In a message dated 3/8/2016 3:20:58 P.M. Central Standard Time, sm6wet@telia.com writes: Jag har från och med 8:e mars inte läng
Jag har från och med 8:e mars inte längre tillgång till denna mejl pga en tjänsteresa. Om du försöker att anmäla dig till VII:e graden i Skara 13/3 så var sista anmälningsdatum söndagen 6/3. Jag komm
Author: TexasRF--- via TowerTalk <towertalk@contesting.com>
Date: Tue, 8 Mar 2016 16:37:50 -0500
Jag har från och med 8:e mars inte längre tillgång till denna mejl pga en tjänsteresa. Om du försöker att anmäla dig till VII:e graden i Skara 13/3 så var sista anmälningsdatum söndagen 6/3. Jag komm
My usual go-to chemical anchor epoxy for this kind of application is Hilti HY-200. I also like Hiti's HIT-Z anchor rods, but they aren't available in hot-dip galvanized unfortunately; give them a sh
-- Jeff WN3A -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus _______________________________________________ __________________________________
The post is in Swedish. Seems like a virus got in to the guys machine. 73 Bert, VE3NR -- Jeff WN3A -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivi
YES, It is a standard "I will be out of the office" message in Swedish .. jag ar svensk poika! At their work my daughters both use such messaging when they are to be gone for a day or more. Unfortuna
I was joking, hence the smiley. Just like this one :-) -- Jeff WN3A -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __________________________