This is why I have a delete key.
73
Jim W7RY
-----Original Message-----
From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
On Behalf Of Peter Chadwick
Sent: Tuesday, August 01, 2006 1:27 PM
To: amps@contesting.com
Subject: [Amps] Amplifier frustrations
A tale that may amuse, and may even evoke sympathy........
Last year, I changed antennas. The 205BA at 62 feet and interlaced 4 ele
beams for 10 and 15 at 68 feet went, replaced by a 4 ele Steppir at 62
feet. The tower, fed as folded monopole, moved its resonance from 2.6 to
3.72MHz. No longer could it be fed with an L network with a variable C -
it needed variable L as well. Built a remote controlled tuner, using a
vacuum variable that I'd been given. Hi Pot? never needed
one.........beautiful purple glow in the variable. Anybody know where I
can get a new vacuum for it? SWR went through the roof, of course. Tried
a smaller vac variable, and tried making a padder capacitor out of sheet
glass. More fireworks, and SWR again through the roof. Tried some HV
ceramic capcitors and they couldn't cut it either - more fireworks. So I
bought a cap from Max Gain systems, and eventually got the mechanics
sorted out for the motor drive.
I then found that the periods of arcing in the tuner appeared to have
screwed the amp. It would work on 3.5 MHz, but even into dummy load,
went mad at 3.7. I changed the passive grid resistor to a Tin-Oxide,
and still it went mad. Plate current runs away, and I think the bias
from the regulated bias supply collapses, because the interlock drops
out. OK on 20. The RF choke was definitely small, and I played with
that, with two chokes in series. One of them was from the NCL2000, and
being held off by about 85 microhenries from the full RF at the plate, I
was surprised when that had the smallest 'pi' start burning up on 40 -
from the outside. That took the series HV fuse. Stripped burnt wire off,
intennding to have another go. KH8SI appears, and I've no amp. This
morning, he's actually gotten around to working EU 30 minutes after the
band opened on 20, but I can't cut it without an amp - I did try.... Try
firing up the amp after the work on teh RC choke. Before the amp was put
into tx, there was a sparking noise. Open everything up, and check. HV
fuse OK, remember Tom Rauch's comments on equalising resistors and Rich
Measures comments on wirewounds. Measure them. There's 8 off 22k and 2
off15k in series across the elctrolytic string, and they measure about
900k ohm. Figure this needs looking into. Go to one capacitor with 22k
across it. Put meter across, and watch the resistance climb as the cap
charges. gets up to about 30 K. OK. Disconnect capacitor from resistor,
check resistor again. 22.1K. Add capacitor and resistance goes UP!!
Repeat a few more times, wondering 'what the hell?' Why should 800 mFd
across a 22k resistor make the DVM indicate a higher than 22k
resistance. Get out the AVO - old fashioned VOM - and that gives
sensible readings. Then note DVM is intermittently flashing to say the
battery is low. Change battery, and sensible readings obtained. But that
is a new one on me that the DVM can be that wrong before it indicates
low battery. Oh well, I got it for nothing anyway...Probably something
to do with spikes from the sampling integrating.
Go back to chasing the sparks. Of course, this is where you need a Hi
Pot. Havn't got one. there's a HV xfmr under the ebnch supposed to be
for a scop. Check it, get 1700 volts. two K2AW rectifiers, a couple of
caps, drive it from a Variac and we have a hiPot going up to 4.4kV. Now
I can use that 40kV probe for the DVM.....apply to amp, sparking. Turns
out that there's an open on the RF choke that was sparking. Sort that
out.
Try firing up on 160, efficiency poor, and suddenly the mains fuse for
the HV goes.. No spares.....drill ends of fuse and fit 30 gauge copper
wire. NOT best practice with the inside of the glass copper coated.
Decide to try 20meters in case KH8SI is there again tomorrow morning -
they've probably gone home, or conditions will be bad or something.
Still, it seems to fire up on 20 tonight. Leave it alone....
Conclusions. This nearly 50 year old amp, the Rf deck of which was
designed for the military as a lower power tx and uprated with bigger
valves and more volts by the OEM, has probably got some components (for
which I don't have, and can't readily get, spares) breaking down under
RF load as a result of the SWR when the arcing took place They are hard
to pinpoint because when they let go, all hell lets loose and the thing
blows fuses, and at lower power, theyr'e OK..
I've even got so depressed I've been looking up the prices of
Ameritrons......about the same number of pounds here as they are dollars
in the US. That is even more depressing....
The DVM thing is something totally new to me. Anyone else seen anything
like it? Hopefully, someone may learn soemthing from this tale of
woe....maybe that buying an Ameritron is a better idea than trying to
build your own or rework surplus!
73
Peter G3RZP
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|