That's correct. Each copy of MMTTY needs to have its own separate setup -
that's why they are run from two separate folders, because MMTTY stores its
configuration data in the same folder as the executable and the two copies
need to have different configurations, hence need to be started from
different folders. If you are using a stereo sound card with the left
channel fed from one radio and the right channel fed from the other radio,
each copy of MMTTY must be configured to use the channel that is used by
its radio; if you are using two sound cards, one for (or in) each radio,
then each copy of MMTTY must be configured for the applicable sound card.
If you are using FSK, each copy of MMTTY must use its own separate serial
port for FSK keying.
See <
http://n1mm.hamdocs.com/tiki-index.php?page=SO2R+-+Single+Operator+Two+Radio+Operation&structure=N1MM+Logger+Documentation#SO2R_and_MMTTY>
for instructions on doing this with N1MM+. The details may be different
with other logging programs, but the principles should be the same.
73,
Rich VE3KI
On Sat, Dec 15, 2018 at 8:27 PM WW3S <ww3s@zoominternet.net> wrote:
> Change the audio input for each instance of mmtty running....I use left on
> one radio and right on the other....same with ptt, if in separate
> directories with separate ini files they are separately configurable....if
> you are using n1mm, once you get them set, close each di window, while
> leaving mm run, then reopen the di windows again, that’s how it makes the
> config “sticky”.....
>
> Sent from my iPad
>
> > On Dec 15, 2018, at 6:32 PM, sbloom@acsalaska.net wrote:
> >
> >
> >
> >
> >
> > Rich,
> >
> > Have done all that, but forgot one important detail. I"m using a
> MK2R+ which does the audio routing. Both instances load with the
> correct configuration, but .. still
> >
> > 1) Both Digital windows decode signals from Radio 1
> > 2) There is no PTT to Radio 2
> >
> > Even more mysterious, this happens, I still have decode on Window1 even
> if I turn the USB router software for the MK2R+ off. I *thought* the
> router was required for any audio passthrough.
> >
> > 73
> > Steve KL7SB
> >
> >
> >
> > On Sat, 15 Dec 2018 17:32:27 -0500, Richard Ferch wrote:
> >
> > Steve,
> >
> > Don't try to *install* MMTTY twice. Install it once, then create a new
> > folder somewhere and *copy* the mmtty.exe, mmtty.ini and userparms.ini
> > files into the new folder (also any extfsk files, if you use any of
> those).
> > If you want to run the second copy stand-alone, you might want to copy
> the
> > other files from the first MMTTY program folder into the second folder,
> and
> > create a second desktop shortcut, but this is not necessary if you always
> > run MMTTY from inside a logging program. Configure your logging software
> to
> > point to the first copy for Radio 1 and the second copy for Radio 2.
> >
> > 73,
> > Rich VE3KI
> > _______________________________________________
> > CQ-Contest mailing list
> > CQ-Contest@contesting.com
> > http://lists.contesting.com/mailman/listinfo/cq-contest
> >
> >
> >
> >
> > _______________________________________________
> > CQ-Contest mailing list
> > CQ-Contest@contesting.com
> > http://lists.contesting.com/mailman/listinfo/cq-contest
>
>
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
|