Don't even connect it to the radio to test. Type SOUND to turn on the PC
speaker and you will get sidetone from the PC. That way you can check out your
computer setup regardless of the radio.
>Hi David,
>
>Thanks for the response.
>
>This is my first attempt. Running 5 watts into a dummy load.
>Wiring looks good. Single dits and dahs work okay. Putting
>them together creates garbage, after the initial good first
>letter. Tried Super CMOS, Curtis A, and Curtis B modes with
>no difference. Tried two different paddles with no difference.
>
>Was thinking about performing an exorcism. 8^)
>
>73,
>Bob
>
>----- Original Message -----
>From: "David Robbins K1TTT" <k1ttt@arrl.net>
>To: "reflector ct-user" <ct-user@contesting.com>
>Sent: Thursday, June 26, 2003 4:20 PM
>Subject: RE: [ct-user] CT 9.90.007 and Paddle
>
>
>> Check that you aren't getting rf into the port... turn off or reduce
>> radio power. Doublecheck wiring and pin numbers, make sure no pins are
>> shorted and that pullup resistors are properly connected. Slow the
>> speed way down and try to send single dits and dahs to see if maybe you
>> have bounce in a paddle contact. Has it worked with earlier versions on
>> that machine or is this your first attempt??
>>
>>
>> David Robbins K1TTT
>> e-mail: mailto:k1ttt@arrl.net
>> web: http://www.k1ttt.net
>> AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
>>
>>
>> > -----Original Message-----
>> > From: ct-user-bounces@contesting.com [mailto:ct-user-
>> > bounces@contesting.com] On Behalf Of Bob Schreibmaier
>> > Sent: Thursday, June 26, 2003 20:00
>> > To: ct-user@contesting.com
>> > Subject: [ct-user] CT 9.90.007 and Paddle
>> >
>> > I tried to use CT 9.90.007 and an external paddle on
>> > a Toshiba 486/50 laptop (QRP Field Day computer)
>> > running MS-DOS 6.22. I used the REVPADDLE command
>> > to get the left paddle to send dits and the right
>> > to send dahs.
>> >
>> > Sending with the motion necessary to send a "V",
>> > the first letter out is a "V", but the next one is an
>> > "F", followed by something unintelligible.
>> >
>> > I've tried not using REVPADDLE, but simply changing
>> > the paddle around. Same results.
>> >
>> > Has anyone else seen this behavior? Is it possible
>> > to fix?
>> >
>> > TIA.
>> >
>> > 73,
>> > ____ / _____ /
>> > / ) / / /
>> > /____/ ____ /___ (____ ____ /___ /___
>> > / ) / ) / ) ) / / ) /
>> > /_____/ /____/ /____/ _____/ (____ / / / . . .
>> >
>> > +---------------------------------------------------+
>> > | Bob Schreibmaier K3PH | E-mail: k3ph@ptd.net |
>> > | Kresgeville, PA 18333 | http://home.ptd.net/~k3ph |
>> > +---------------------------------------------------+
>> >
>> > _______________________________________________
>> > CT-User mailing list
>> > CT-User@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/ct-user
>>
>>
>>
>> _______________________________________________
>> CT-User mailing list
>> CT-User@contesting.com
>> http://lists.contesting.com/mailman/listinfo/ct-user
>>
>
>_______________________________________________
>CT-User mailing list
>CT-User@contesting.com
>http://lists.contesting.com/mailman/listinfo/ct-user
CONFIDENTIALITY NOTICE: This message is a PRIVATE communication. This email may
contain privileged and confidential information intended only for the
above-named
recipient. If you have received this in error and you are not the intended
recipient, you are hereby notified that any use, dissemination, or copying is
strictly prohibited. In such case, do not read, copy, or use it, and do not
disclose
it to others. Please notify the sender of the delivery error by replying to this
message, and then delete it from your system. Thank you.
|