Ron,
I have also heard John, W6FE, on his Flex. It sounded dead clean to me...
I have started recording MP3 audio clips of all these on air encounters, and
will be listing them on an internet server page, so you (or whoever is
interested) can just listen to them over and over again (hihi..) and draw
their own conclusions.
In a detailed QSO tonight with K0SXO and N4ZZ (two very expert contesters
and multiple Orion owners!) they confirmed the audio differences between
software versions and TX audio. I think you maybe heard that QSO as well?
73s few new -Dan K6KDK
----- Original Message -----
From: "Ron Castro" <ronc@sonic.net>
To: <k6kdk@k6kdk.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Tuesday, March 21, 2006 8:51 PM
Subject: Re: [TenTec] [Orion] O2 Tx audio quality
> Whoops....sent that last e-mail before I wrote a message!
>
> I talked to W6FE last night on 3.847 later on in the evening last night,
and
> heard that distortion first hand. He blames it on his 'gravelly voice,
but
> it didn't sound that way to me. There was definitely a problem. He
> switched to a Flex Radio and had the same distortion, so I think it could
be
> in his mic or some other equipment he uses up front of the rigs...or maybe
> it really is his voice!
>
> I'll stop in on that frequency tonight and if you're on, you can listen to
> my O2 and see what you think...
>
> Ron N6AHA
>
> ----- Original Message -----
> From: <k6kdk@k6kdk.net>
> To: <tentec@contesting.com>
> Sent: Monday, March 20, 2006 8:39 PM
> Subject: Re: [TenTec] [Orion] O2 Tx audio quality
>
>
> > ----- Original Message -----
> > From: "Ronald Gorski" <R.Gorski at Astronautics.com>
> > To: "Ron Castro" <ronc at sonic.net>
> > Sent: Monday, March 20, 2006 10:30 AM
> > Subject: Re: [Orion] O2 Tx audio quality
> >
> >
> >>>I heard another O2 user over the weekend who's audio sounded distorted,
> >>>but since I was just getting ready to leave the house I didn't have a
> >>>chance to talk to him. If I run into him again (he's usually around on
> >>>75
> >>>at night) I'll see if I can get an idea about what might be causing his
> >>>problem, and report it back here.
> >>
> >> Please do. I think there are more of us out there. I am starting to
think
> >> that there may be a hardware problem with the audio board.
> >> 73, Ron
> >>
> >>>Ron N6AHA
> >
> > Ron, Yes, there are more of you out there.. I just had QSO w/ N9AU
> > running a O2 (worst audio I ever heard!), last night QSO w/ W6FE, with
> > same breakup on peaks, he was also running O2. This is exactly same
audio
> > break up you get if you run an O1 and load Ver 2.055. But of course if
> > you have O1 you just cure it by going back to Ver 1.371, if you have O2
I
> > don't know what you do about it. Most are handling the frustration by
> > talking themselves into... "must be some sort of RF in the shack"..
> > hihi...
> >
> > -Dan
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|