There is Chem Wik, and everything else. I think MCM carries it, at retail
+.
----- Original Message -----
From: "Dr. Gerald N. Johnson" <geraldj@weather.net>
To: <davkozy@comcast.net>
Cc: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Thursday, April 01, 2010 12:56 PM
Subject: Re: [TenTec] Pegasus 550
> Solder wick. The types with the finer wire in the braid works best. 60
> watt temperature controlled soldering iron.
>
> 73, Jerry, K0CQ
>
> On 4/1/2010 10:36 AM, davkozy@comcast.net wrote:
>> Thanks all for your suggestions!! I did find a source for replacement
>> relays www.onlinecomponents.com <http://www.onlinecomponents.com> that
>> had them in stock. ($1.77 ea. + Shipping) I'm waiting for them to arrive.
>> Hope to find the time to install now with the nice weather setting in.
>>
>> Anyone have any tricks for easy desoldering?
>>
>> Dave KB9EPL
>>
>>
>>
>> ----- Original Message -----
>> From: "phil g" <trapperpg@earthlink.net>
>> To: geraldj@weather.net, "Discussion of Ten-Tec Equipment"
>> <tentec@contesting.com>
>> Sent: Monday, March 29, 2010 2:52:24 PM GMT -06:00 US/Canada Central
>> Subject: Re: [TenTec] Pegasus 550
>>
>> I never noticed the pull-in voltage. I had that link bookmarked in my
>> pegasus files as a replacement. I think it came from this list. I no
>> longer have my 550, but maybe someone out there is adventurous and could
>> do
>> a voltage check.
>>
>> There is a 5v version listed, apparently also made of unobtainium.
>>
>> http://www.newark.com/panasonic-ew/als2b05tw/miniature-power-relay/dp/45M7085
>>
>> n4zsa
>> ----- Original Message -----
>> From: "Dr. Gerald N. Johnson" <geraldj@weather.net>
>> To: <tentec@contesting.com>
>> Sent: Monday, March 29, 2010 2:36 PM
>> Subject: Re: [TenTec] Pegasus 550
>>
>>
>> > The part number indicates a 12 volt coil.
>> >
>> > 73, Jerry, K0CQ
>> >
>> > On 3/29/2010 12:21 PM, Denton wrote:
>> >> I used to have a Peggy, and one of the relays on the band pass filter
>> >> board
>> >> failed...if I remember right, the relay coils for both input and
>> output
>> >> of
>> >> the filter are wired in series...I replaced mine with two new relays
>> that
>> >> had 6 volt coils.
>> >> ----- Original Message -----
>> >> From: "phil g"<trapperpg@earthlink.net>
>> >> To: "Discussion of Ten-Tec Equipment"<tentec@contesting.com>
>> >> Sent: Monday, March 29, 2010 11:04 AM
>> >> Subject: Re: [TenTec] Pegasus 550
>> >>
>> >>
>> >>> Here is a link to the relay. Also avail. from Ten Tec.
>> >>> http://www.newark.com/jsp/search/productdetail.jsp?SKU=45M7086
>> >>>
>> >>> Fairly straight forward to replace. Unsolder the old, solder in the
>> >>> new.
>> >>>
>> >>> n4zsa
>> >>> ----- Original Message -----
>> >>>
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|