No doubt that it's a major issue to get fast QSK with an SDR. I think it's
still an excellent radio and I hope mine lasts as long as I do!
73,
Kim N5OP
"People that make music together cannot be enemies, at least as long as the
music lasts." -- Paul Hindemith
> On Nov 7, 2016, at 04:10, Barry N1EU <barry.n1eu@gmail.com> wrote:
>
> You should try a Corsair II if you want to experience real QSK at higher
> speeds!
>
> BTW, it took a LOT of work to get the Orion as good as it ended up. The
> beta testers were all over TT to improve it in early firmware versions and
> tested/measured the heck out of it.
>
> 73, Barry N1EU
>
>> On Mon, Nov 7, 2016 at 3:35 AM, Kim Elmore <cw_de_n5op@sbcglobal.net> wrote:
>>
>> I've noticed the same thing with my OII but only on 40/80/160 m bands. 2%
>> fixed it with mine as well.
>>
>> Because the radio is essentially SDR, I've noticed that the
>> within-character QSK rx is lost around 20-25 WPM, depending on the QSK
>> delay setting; between characters is always OK at any speed I can handle.
>> On my olde analog TS-930S, the QSK hangs in there pretty much as fast as I
>> care to go.
>>
>> 73,
>>
>> Kim N5OP
>>
>>
>>> On 10/25/2016 6:20 PM, Barry N1EU wrote:
>>>
>>> 2% is nothing, you'll be absolutely fine
>>>
>>> 73, Barry N1EU
>>>
>>> On Tue, Oct 25, 2016 at 5:56 PM, Rod Greene <w7zrc@yahoo.com> wrote:
>>>
>>> Barry,
>>>>
>>>> Sorry if this appears as a repeat message - but I didn't see my previous
>>>> reply come through. Anyway, that fixed it. I can go down as low as 2% but
>>>> not any less.
>>>>
>>>> Thanks much! 73, Rod/w7zrc
>>>>
>>>>
>>>> ------------------------------
>>>> *From:* Barry N1EU <barry.n1eu@gmail.com>
>>>> *To:* Rod Greene <w7zrc@yahoo.com>; Discussion of Ten-Tec Equipment <
>>>> tentec@contesting.com>
>>>> *Sent:* Tuesday, October 25, 2016 3:32 PM
>>>> *Subject:* Re: [TenTec] Audio Popping - Orion II with V3.033xe
>>>>
>>>> Try adding 10% CW QSK Delay in the CW Menu.
>>>>
>>>> 73, Barry N1EU
>>>>
>>>> On Tue, Oct 25, 2016 at 5:26 PM, Rod Greene via TenTec <
>>>> tentec@contesting.com> wrote:
>>>>
>>>> All,
>>>> I just loaded version 3.033xe and have entered all my custom settings. I
>>>> know I'm a little late trying this update. Anyway, all seems to be
>>>> working
>>>> okay except when keying CW. When the key breaks (when I let up on the
>>>> key),
>>>> I get a pop in the audio monitor. Happens all the time even with the
>>>> S-Tone
>>>> at zero.
>>>>
>>>> Is this a known problem and do I just need to go back to version 3.033xd
>>>> to correct it, or have I missed a setting somewhere?
>>>> Thanks and 73, Rod/w7zrc
>>>> ______________________________ _________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/ mailman/listinfo/tentec
>>>> <http://lists.contesting.com/mailman/listinfo/tentec>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>> --
>>
>> Kim Elmore, Ph.D. (Adj. Assoc. Prof., OU School of Meteorology, CCM, PP
>> SEL/MEL/Glider, N5OP, 2nd Class Radiotelegraph, GROL)
>>
>> /"In theory there is no difference between theory and practice. But, in
>> practice, there is." //– Attributed to many people; it’s so true that it
>> doesn’t matter who said it./
>>
>> _______________________________________________
>>
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|