I've mostly used 73 mix tubular and binocular Fair-Rite cores of all sorts
of common-mode chokes on coax and for matching transformers 160/80m
receiving loops and for input match to my 3-500ZG amp. Have had good results
all around I used 73 because it's what I had on hand. Fair-Rite 73 material
is really rugged and seems be very resistant to corrosion etc.
73,
Charlie, K4OTV
-----Original Message-----
From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of Tim
Shoppa
Sent: Wednesday, August 06, 2014 12:45 PM
To: Ron Stordahl, AE5E
Cc: topband@contesting.com; jim@audiosystemsgroup.com
Subject: Re: Topband: Ferrite Cores
#31 is a very nice mix for winding chokes especially at topband and lower HF
and for EMI suppression.
#61 is very common for HF transformers up to medium power levels.
#43 is also useful at HF transformers and chokes especially at upper HF.
#73 is a very nice mix for low band transformers but some of the testing
done shows typical transformers to be good 5kHz-50MHz:
http://www.cliftonlaboratories.com/imd_in_broadband_transformers.htm
I have been using #73 binocular cores for all sorts of things lately. A
little Fair-Rite 2873000202 core works excellently in isolated DC-to-DC
power converters at the several watt power level.
On Wed, Aug 6, 2014 at 11:15 AM, Ron Stordahl, AE5E via Topband <
topband@contesting.com> wrote:
> In this discussion two different ferrite mixes are mentioned: #31 and
> #61.
>
>
> From the descriptions of these on the Fair-Rite web page, it appears
> that
> 31 would be more suitable for lower frequency applications.
>
>
> Is this the case?
>
> Ron, AE5E
>
>
>
> On Wednesday, August 6, 2014 4:02 AM, Charlie <
> charlie-cunningham@nc.rr.com> wrote:
>
>
>
> I agree with all those points, Jim! Over the years, professionally, we
> designed many Fair-Rite, cores into most of our electricity, gas and
> water meter and electricity load-management products and shipped
> millions of Fair-Rite products in our devices. Fair-Rite and Kreger
> are excellent suppliers, and I still have many of their development kits
around here.
> Their products are excellent and very consistent
>
> Lynne Frye, of Kreger, is a very helpful contact person, that I have
> worked with over the years!
>
> Have a good day!
>
> 73,
> Charlie Cunningham, K4OTV
>
>
>
> -----Original Message-----
> From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of Jim
> Brown
> Sent: Tuesday, August 05, 2014 3:00 PM
> To: topband@contesting.com
> Subject: Re: Topband: Ferrite Cores
>
> On 8/5/2014 11:36 AM, Mike Waters wrote:
> > FT-240-61 cores. Amidon was $9/ea, Mouser (for the Fair Rite
> > equivalent)
> > >was $14/ea.
>
> The actual manufacturer of a 2.4-in o.d. #61 toroid IS Fair-Rite. It
> is not an "equivalent," #61 material is Fair-Rite's mix. Other
> companies may make a "knock-off," but the REAL part is made by
> Fair-Rite.
>
> 73, Jim K9YC
>
>
> _________________
> Topband Reflector Archives - http://www.contesting.com/_topband
>
>
> ---
> This email is free from viruses and malware because avast! Antivirus
> protection is active.
> http://www.avast.com
>
> _________________
> Topband Reflector Archives - http://www.contesting.com/_topband
> _________________
> Topband Reflector Archives - http://www.contesting.com/_topband
>
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
---
This email is free from viruses and malware because avast! Antivirus protection
is active.
http://www.avast.com
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
|