Ok since the mailing list stripped my diagram out, it can
be viewed at my website:
http://home.xnet.com/~sjwoodr/ham/cw_ptt.jpg
tnx
/steve n9oh
----- Original Message -----
From: "Steve Woodruff" <sjwoodr@yahoo.com>
To: "Gil Baron" <gbaron@charter.net>; <writelog@contesting.com>
Sent: Friday, November 08, 2002 9:25 PM
Subject: RE: [WriteLog] ptt line resistance?
> Ok, i'm attempting to attach a JPG of my
> circuit. Hopefully the reflector doesn't
> strip out attachments automatically. :)
>
> Its actually a NPN 2n2222 transistor that
> i'm using. See attached diagram.
>
> You mentioned to use a PNP if "positive
> keying" ... not sure if that is my case or
> not. Rig is ic706mk2g. digging out the
> manual now...
>
> tnx
>
> /steve n9oh
>
> --- Gil Baron <gbaron@charter.net> wrote:
> >
> >
> > > -----Original Message-----
> > > From: writelog-admin@contesting.com
> > > [mailto:writelog-admin@contesting.com]On Behalf Of
> > Steve Woodruff
> > > Sent: Friday, November 08, 2002 8:57 PM
> > > To: writelog@contesting.com
> > > Subject: [WriteLog] ptt line resistance?
> > >
> > >
> > > I now have all mode ptt via cw line RTS.
> > > However... its not working. When i play
> > > SSB messages it is not triggering the
> > > rig's PTT line. I am connecting to the
> > > same port that my footswitch normally
> > > connects to... simple mono plug.
> > >
> > > When i hit a F-# button to play a message,
> > > i can see with a multimeter the resistance
> > > on my PTT line drop down to about 4-6 ohms.
> > > Not much.... but is that enough to keep the
> > > rig from triggering PTT?? If so, how can
> > > i drop the resistance?
> >
> > Be sure the diode is not in the wrong direction. You
> > did not give enough
> > information to really understand your circuit.
> > Perhaps a text based drawing
> > would help. I use no diodes, just a 4.7 k or so to
> > the base and the radio
> > directly connected to the collector with no
> > resistance.
> >
> > Be certain the Transistor is a PNP if Positive
> > keying.
> >
> > Be certain the correct polarity is used from the
> > RTS.
> >
> >
> > If your resistance to ground with an Ohmmeter at the
> > Collector of the
> > transistor is as low as 5 ohms I do not see why the
> > rig does not key? Try
> > just a plain resistor to see what it needs on the
> > rig. I bet over 100 ohms
> > would still key it.
> >
> >
> >
> > >
> > > my ptt circuit uses RTS from the cw serial
> > > port, goes through a 4k7 resistors, then
> > > in parallel with a diode and another 4k7
> > > before hitting a 2n2222.... and then a
> > > final diode before having a PTT + and a
> > > ground line.
> > >
> > > Any ideas? tnx
> > >
> > > Steve, n9oh
> > >
> > >
> > > __________________________________________________
> > > Do you Yahoo!?
> > > U2 on LAUNCH - Exclusive greatest hits videos
> > > http://launch.yahoo.com/u2
> > > _______________________________________________
> > > WriteLog mailing list
> > > WriteLog@contesting.com
> > >
> >
> http://lists.contesting.com/mailman/listinfo/writelog
> > >
> >
> >
>
>
>
> =====
> ----------------------------------------------------------
> Steve Woodruff, N9OH @ 42.18N 88.34W, sjwoodr@yahoo.com
>
> __________________________________________________
> Do you Yahoo!?
> U2 on LAUNCH - Exclusive greatest hits videos
> http://launch.yahoo.com/u2
>
> --- StripMime Report -- processed MIME parts ---
> multipart/mixed
> text/plain (text body -- kept)
> image/pjpeg
> ---
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
>
>
|
