Thanks Gentleman!! many
I thought anything inside [brackets] was a user comment
nope
follow the instructions exactly - got it
IT WORKS !!! THANKS
CU This weekend in test
73 Robert W5AJ @ P40P
On Fri, Mar 3, 2017 at 10:32 AM, Mike Heideman <mike_heideman@hotmail.com>
wrote:
> Instead of [KeyboardShortcuts] you should define the macros in an
> [Elecraft_K3_Commands] section of writelog.ini:
>
> [Elecraft_K3_Commands]
> Macro_10=SWT21;
> ...
>
>
> Follow the steps in the following link exactly and you should be able to
> both play back and record messages using the F keys. This should give you a
> good starting point and you can then tweak things from there.
>
>
> http://lists.contesting.com/_writelog/2016-11/msg00063.html
>
>
> 73,
>
> -Mike, N7MH
>
>
> Robert, W5AJ, wrote:
>
> ________________________________
>
> At P4 station and can't get the F keys to fire the K3 DVR
> K3, DVR works fine from M1 key on front panel
> COM2 is used for rig control
> thoughts anyone??
>
> Version 12.06b
>
> I export to writelog.ini
> edit in
> [KeyboardShortcuts]
> Macro_10=SWT21;
>
> in the message keys for SSB
> %GK10
>
> but nothing happens at K3....
> Rig frequency is correctly displaying in writelog btw
>
> 73 Robert W5AJ
>
>
> On Tue, Feb 28, 2017 at 2:58 AM, Mike Heideman <mike_heideman@hotmail.com<
> mailto:mike_heideman@hotmail.com>> wrote:
> Robert, W5AJ, wrote:
> > Is there any method that will allow function key (say F1) to send
> message in
> > Bank1 M1
> > And then allow function key (say F5) to send message in Bank 2 M1
> > Without holding the REC button...
> > So the F key always defines which bank / M without issuing command to
> switch
> > banks
>
> The only control for changing K3 DVR memory banks is a toggle, either via
> the REC hold or the equivalent SWH37; sent from the computer. The K3
> Programmer's Reference documents a method for retrieving the current memory
> bank which could be used by software to conditionally switch banks,
> enabling two function keys to play back the M1 message in each of the two
> banks. Unfortunately the Writelog macros do not provide a way of retrieving
> a response to a CAT command sent to the K3.
>
> The details of how Writelog could be modified to implement this behavior
> are in this post I made in November.
>
> http://lists.contesting.com/archives//html/WriteLog/2016-11/msg00068.html
>
> I think that Wintest may be capable of interpreting responses to CAT
> commands which would enable the direct addressing of all 8 DVR memories.
>
> In some recent phone contests I set up Shift-F5 to toggle the DVR memory
> banks. My main purpose was so that I could occasionally throw in a longer
> CQ while Auto-CQing. This had one major drawback - since the Timed-CQ
> interval must be specified as the time between the starts of successive
> CQs, not the time between the end of one CQ and the start of the next CQ,
> the next CQ after a long CQ would start up too early, before I'd typed even
> one character of a callsign.
>
> 73,
> -Mike, N7MH
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com<mailto:WriteLog@contesting.com>
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|